-
Welcome to the Contour Enthusiasts Group, the best resource for the Ford Contour and Mercury Mystique.
You can register to join the community.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an alternative browser.
You should upgrade or use an alternative browser.
underdrive pulley
- Thread starter robo519
- Start date
95pgt-t
Hard-core CEG'er
asp still makes one for the duratec..check ebay under cougar or something. unorthodox used to,but i'm not srue they do anymore. i personally liked the mod...others will chime in and tell you this and that.
http://cgi.ebay.com/ebaymotors/ASP-...ptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories
You usually can't find them on ebay. I think it's ASP that sells the 3 pulleys together for a little over $200 shipped, as well.
You usually can't find them on ebay. I think it's ASP that sells the 3 pulleys together for a little over $200 shipped, as well.
BlackBetty
CEG'er
I have an ASP in the Cougar, it was a nice little mod. But they only sold the UDP when I bought it.
CSVT1214
Addicted CEG'er
yea, thats a good quesion..wern't they the same motors in the mx6?
No...
yea, thats a good quesion..wern't they the same motors in the mx6?
No....i am referring to the 3.0L dohc engine that was used.
Dyoel182
Addicted CEG'er
The mx6 never got a 3.0 engine though.
:nonono: mazda 6 and mx6 two different carsThe mx6 never got a 3.0 engine though.
Dyoel182
Addicted CEG'er
:nonono: mazda 6 and mx6 two different cars
Exactly. Which is why I wondered what Robo and then Harry were talking about.
striker2
Official CEG Vendor
they sell a 3 piece pulley set for the mazda 6:shrug:
I wonder if those would fit on our cars?
Well the crank and alternator should...:shrug:
Exactly. Which is why I wondered what Robo and then Harry were talking about.
Harrry was talking about the 6 the whole time. not the Mx6
Dyoel182
Addicted CEG'er
And now you've brought the 626 into it. I guess I might as well mention the Probe and get the whole GD, GE and GF family in.
I saw where Harry mentioned the 6 but he replied to the Robo question about it being the same engine as the mx6.
I saw where Harry mentioned the 6 but he replied to the Robo question about it being the same engine as the mx6.
striker2
Official CEG Vendor
oops. read over robos post to fast and it didnt register. :troutslap:And now you've brought the 626 into it. I guess I might as well mention the Probe and get the whole GD, GE and GF family in.
I saw where Harry mentioned the 6 but he replied to the Robo question about it being the same engine as the mx6.
And now you've brought the 626 into it. I guess I might as well mention the Probe and get the whole GD, GE and GF family in.
I saw where Harry mentioned the 6 but he replied to the Robo question about it being the same engine as the mx6.
I never said its the same engine???
I said NO.......etc etc
Dyoel182
Addicted CEG'er
I never said its the same engine???
I said NO.......etc etc
Agreed. You said it was not the same and corrected him.
Agreed. You said it was not the same and corrected him.
Noooo....you agreed i said NOOO :laugh:
Bradness
CEG'er
tryin to find some but can't seem to find them anywhere! any help but be appreciated!
If you're interested in used I have 1 each of UR and ASP. The ASP has been lightened further. I've had 1 or the other on all my motors and can attest to the usefulness (better mileage & noticeable improvement in engine acceleration) on a long term basis.
PM me if you're interested-I'd be looking for about $50 depending on which 1 you want.
DemonSVT
CEG'er
FluidAmpr makes a wonderful underdrive crank pulley. (See 3L Mazda 6 - yes it fits)
It is a bit pricey but is worth every penny IMNSHO. Far superior to any stock offering in taming NVH and torsional bending. It is 10% under-driven.
I can't recommend running an aftermarket pulley without the damper but there is real world proof that "if" you keep the engine rpm down (i.e. under 6700) you can run one for extended periods of time without failure. You can search for a few very detailed write-ups on this subject.
It is a bit pricey but is worth every penny IMNSHO. Far superior to any stock offering in taming NVH and torsional bending. It is 10% under-driven.
I can't recommend running an aftermarket pulley without the damper but there is real world proof that "if" you keep the engine rpm down (i.e. under 6700) you can run one for extended periods of time without failure. You can search for a few very detailed write-ups on this subject.