blu_fuz
New Member Classroom vulture
This is a good guide for wheel studs when you add a 3mm-10mm spacer to your Contour/Mystique.
Stock:
KNURL DIAMETER: 13.08mm
LENGTH: 42mm
SHOULDER LENGTH: 15mm
OEM replacement:
DORMAN part number 610-306:
Orilley's $1.99 EA
Rockauto $1.14 EA
KNURL DIAMETER: 13.08mm
LENGTH: 48mm (threaded length is identical to stock - OEM replacement, not longer)
SHOULDER LENGTH: 15mm
These studs listed below are for "longer than stock" studs.
Belkamp part number 641-3131:
NAPA $2.39EA + $10.99 UPS flat rate charge because they don't have them in stock
KNURL DIAMETER: 13.08mm
LENGTH: 52mm
SHOULDER LENGTH: 25.5mm
DORMAN part number 610-341:
Orilley's $2.49 EA ($39.84 at the store)
Rockauto $1.43 EA ($38.86 shipped with 5% coupon for 20)
KNURL DIAMETER: 13.08mm
LENGTH: 52mm
SHOULDER LENGTH: 25.5mm
*Made for a 1986 Mazda RX7*
ARP part number 100-7708
Online $60.45 for 20 studs shipped
KNURL DIAMETER: 0.509 in. (approx 13mm)
LENGTH: 2.500 in. (approx 64mm) (close ended lug nuts might not fit with this length of wheel stud)
SHOULDER LENGTH: 0.315 in. (approx 8mm)
Here is the how-to video I made for the rear disc brake hubs
(note: I have the Milan 12" big brake kit and 1/4" spacer installed on the rear, your results/process may vary) :
http://www.youtube.com/watch?v=WV4Nb2NeW9c&feature=g-upl
Here is the how-to video I made for the front disc brake hubs
(note: I have the 13" BAER big brake kit and 1/4" spacer installed on the front, your results/process may vary) :
http://www.youtube.com/watch?v=1IY0TziZ_-0&feature=g-crec-u
Stock:
KNURL DIAMETER: 13.08mm
LENGTH: 42mm
SHOULDER LENGTH: 15mm
OEM replacement:
DORMAN part number 610-306:
Orilley's $1.99 EA
Rockauto $1.14 EA
KNURL DIAMETER: 13.08mm
LENGTH: 48mm (threaded length is identical to stock - OEM replacement, not longer)
SHOULDER LENGTH: 15mm
These studs listed below are for "longer than stock" studs.
Belkamp part number 641-3131:
NAPA $2.39EA + $10.99 UPS flat rate charge because they don't have them in stock
KNURL DIAMETER: 13.08mm
LENGTH: 52mm
SHOULDER LENGTH: 25.5mm
DORMAN part number 610-341:
Orilley's $2.49 EA ($39.84 at the store)
Rockauto $1.43 EA ($38.86 shipped with 5% coupon for 20)
KNURL DIAMETER: 13.08mm
LENGTH: 52mm
SHOULDER LENGTH: 25.5mm
*Made for a 1986 Mazda RX7*
ARP part number 100-7708
Online $60.45 for 20 studs shipped
KNURL DIAMETER: 0.509 in. (approx 13mm)
LENGTH: 2.500 in. (approx 64mm) (close ended lug nuts might not fit with this length of wheel stud)
SHOULDER LENGTH: 0.315 in. (approx 8mm)
Here is the how-to video I made for the rear disc brake hubs
(note: I have the Milan 12" big brake kit and 1/4" spacer installed on the rear, your results/process may vary) :
http://www.youtube.com/watch?v=WV4Nb2NeW9c&feature=g-upl
Here is the how-to video I made for the front disc brake hubs
(note: I have the 13" BAER big brake kit and 1/4" spacer installed on the front, your results/process may vary) :
http://www.youtube.com/watch?v=1IY0TziZ_-0&feature=g-crec-u