After much internal debate and teeth gnashing, I have finally decided to stop being a miser and sell some of the spares that I will never need and allow them to move on to a new home where they will be appreciated and I hope used in the manner to which they were intended.
The first things to go is what I believe to be the complete stainless steel hand fabricated header and exhaust system from the Mirko Contour that was used in the World Challenge series. These one of a kind headers are constructed to the highest standards with anti-reversion cones, stepped pipes and Burns venturi Collectors. They have bungs for O2 sensors and finish off in 2 1/2 collectors. They are very long tube headers and wrap around the passenger side of the oil pan. They are about the best set of headers that are available for the 2.5L V6 Contour/Cougar vehicle. They are designed to work with a race exhaust that consists of an X-pipe and true duals through hand made mufflers to dumps that drop the exhaust just before the rear sub frame. They are better constructed than the ones I have on my car, but I can't use the set as the exhaust routes right through where my fuel cell is. The Mirko car made about 15 more HP than mine does using this setup.
I am offering these at a super price in the hope that they will go to someone who will use them properly. I am looking for $800 for the headers and $200 for the exhaust system.
I have also decided to sell my brand new set of custom made double adjustable Morrisdampers. These are bolt in for all Contours, Cougars and early 2000 era Focus'. They have remote gas cartridges and adjustable bases to set ride height. They require you to charge them with nitrogen, set the ride height and use 2 1/2 ID by 7 or 8 inch springs. Like I said before, these are brand new and never been used. They are completely rebuildable and adjustable for both compression and rebound. They are a very beefy design and will easily stand up to all road use. I will go over to the shop and take pictures of the front and rears. I was going to adapt them for use in my RX7, but decided not to Butcher them. I just want to see them used by someone who appreciates them. I am looking for $800 for all four.
Prices are F.O.B. Oakville Ontario and as the shipping may be costly, I am willing to work with purchasers to get them to you in as cost effective way as possible.
You can P.M. me here or send me an email at eric.nummelin at helaspice dot com if you are interested or have any questions. If they don't sell here in the next 2 weeks, I will put them on EBay.
Eric
The first things to go is what I believe to be the complete stainless steel hand fabricated header and exhaust system from the Mirko Contour that was used in the World Challenge series. These one of a kind headers are constructed to the highest standards with anti-reversion cones, stepped pipes and Burns venturi Collectors. They have bungs for O2 sensors and finish off in 2 1/2 collectors. They are very long tube headers and wrap around the passenger side of the oil pan. They are about the best set of headers that are available for the 2.5L V6 Contour/Cougar vehicle. They are designed to work with a race exhaust that consists of an X-pipe and true duals through hand made mufflers to dumps that drop the exhaust just before the rear sub frame. They are better constructed than the ones I have on my car, but I can't use the set as the exhaust routes right through where my fuel cell is. The Mirko car made about 15 more HP than mine does using this setup.
I am offering these at a super price in the hope that they will go to someone who will use them properly. I am looking for $800 for the headers and $200 for the exhaust system.
I have also decided to sell my brand new set of custom made double adjustable Morrisdampers. These are bolt in for all Contours, Cougars and early 2000 era Focus'. They have remote gas cartridges and adjustable bases to set ride height. They require you to charge them with nitrogen, set the ride height and use 2 1/2 ID by 7 or 8 inch springs. Like I said before, these are brand new and never been used. They are completely rebuildable and adjustable for both compression and rebound. They are a very beefy design and will easily stand up to all road use. I will go over to the shop and take pictures of the front and rears. I was going to adapt them for use in my RX7, but decided not to Butcher them. I just want to see them used by someone who appreciates them. I am looking for $800 for all four.
Prices are F.O.B. Oakville Ontario and as the shipping may be costly, I am willing to work with purchasers to get them to you in as cost effective way as possible.
You can P.M. me here or send me an email at eric.nummelin at helaspice dot com if you are interested or have any questions. If they don't sell here in the next 2 weeks, I will put them on EBay.
Eric