|
|
Joined: Jun 2002
Posts: 50
CEG\'er
|
OP
CEG\'er
Joined: Jun 2002
Posts: 50 |
I just recently had my timing belt replaced and now I am getting cel code 1381.Does anyone know how I can fix this problem?
Realness
1999 Ford Contour LX
|
|
|
|
Joined: Sep 2000
Posts: 9,602
Hard-core CEG'er
|
Hard-core CEG'er
Joined: Sep 2000
Posts: 9,602 |
Does the car run & drive fine?
That code could point to the cam gears not being lined up properly (cams timed incorrectly)
2000 SVT #674
13.47 @ 102 - All Motor!
It was not broke; Yet I fixed it anyway.
|
|
|
|
Joined: Mar 2002
Posts: 2,319
Hard-core CEG'er
|
Hard-core CEG'er
Joined: Mar 2002
Posts: 2,319 |
Timing belt installation was perhaps not done properly, return to shop to have them examine and correct problem.
98 Mystique LS v6 atx 163,000km
97 Contour LX v6 atx 163,000km
|
|
|
|
Joined: Jun 2002
Posts: 50
CEG\'er
|
OP
CEG\'er
Joined: Jun 2002
Posts: 50 |
My car seems to be running normal. I just can't seem to figure out why I am receiving that code. I dropped my car off where I got it fixed this morning. I hope the mechanic can figure out that the cam gears are not lined up properly if that is problem. Also where are cam gears located? (my guess is they are located between the timing belt) And how can you tell if they are lined up properly?
Realness
1999 Ford Contour LX
|
|
|
|
Joined: Jul 2000
Posts: 1,044
Hard-core CEG'er
|
Hard-core CEG'er
Joined: Jul 2000
Posts: 1,044 |
P1381 Cam Timing Advance is excessive.
They put the belt on just a little bit wrong when it was replaced. One tooth off on the cam pulley is only about 3 degrees so the engine will run OK, but not as well as it should. Gas mileage, performance and emmisions are probably off a little.
|
|
|
|
Joined: Jun 2002
Posts: 50
CEG\'er
|
OP
CEG\'er
Joined: Jun 2002
Posts: 50 |
Thanks for the feedback! I hope everything turns out well!
Realness
1999 Ford Contour LX
|
|
|
|
Joined: May 2001
Posts: 2,291
Hard-core CEG'er
|
Hard-core CEG'er
Joined: May 2001
Posts: 2,291 |
Are you seriously down on power under 3k?? I know I am w/ code 1380 (VCT overretarded). It's a pain to get the timing just right. W/out that damn bolt that holds the crank so piston 1 is at TDC I'd say it's near impossible. Can't wait to get that thing and be done w/ this issue.
If it's very close, 1 tooth will throw you off tremendously. That's what I did at first and it was ridiculous. Ended up loosening the cam gears so I could adjust the cams independently.
|
|
|
|
Joined: Jun 2002
Posts: 50
CEG\'er
|
OP
CEG\'er
Joined: Jun 2002
Posts: 50 |
My power seems to be fine. I don't know what is causing code 1381, I guess something is off. The car is running fine. Now that I think about it when the car is in park it seems to idle just a little slightly rough (just little) not much.
Realness
1999 Ford Contour LX
|
|
|
|
|
|