|
Joined: Sep 2000
Posts: 1,757
Hard-core CEG'er
|
OP
Hard-core CEG'er
Joined: Sep 2000
Posts: 1,757 |
Hey everyone,
I have posted this over in the Duratec forum as well.
Currently DemonSVT and I are putting together a FAQ that will be updated regularly with a lot of quality information. I wanted to extend on this a bit, and have an exhaust database.
That way, there would be one webpage with all sorts of exhaust options, real-world opinions, video clips, and sound clips. This is where I need your help though!
If you have a modified exhaust, you can help out!
What I will need from you:
Name:
Board name:
Engine/Tranny: (SVT V6/MTX...)
Detailed list of your exhaust mod: (I.E... 2.25" Mandrel bent single pipe with a 2" resonator to 2" quasi-dual pipes with baffled rear mufflers and 2.5" tips.)
Cost/Installation Charge: I.E...$500 for the parts, and $100 for the install.
Opinion: (what it sounds like when cold/warm. rasp? droan?)
Misc. Info: (anything that would be helpful to aide someone in their exhaust decision.)
Feel free to email me as well! Contact me via PM or Email about sound/video clips!
Thanks everyone for your time, hopefully it will be a big success! Mods, if you can sticky this topic, it would be greatly appreciated!
-Andy
drryzeabove@hotmail.com
|
|
|
|
Joined: Jan 2002
Posts: 1,939
Hard-core CEG'er
|
Hard-core CEG'er
Joined: Jan 2002
Posts: 1,939 |
Thomas Boomershine T-red2000se Zetec ATX SVT exhaust $20 parts, $40 install Sounds perfect...nice low growl, but won't wake the neighbors. Installation is a pain on the Zetec. Having no Y-pipe, you're left about a foot short for the connection. Have a plasma cutter handy and cut the pipe from the resonator to the connecting flange from you stock exhaust. Do same for SVT exhaust. Trade them, and weld on, making sure that the exhaust hanger peg is lined up correctly. Also note: Need an exhaust hanger on pass. side.
2000 Silver Frost SVT
# 1637/2150
D.O.B. 01/14/2000
|
|
|
|
Joined: Apr 2001
Posts: 9,442
Addicted CEG\'er
|
Addicted CEG\'er
Joined: Apr 2001
Posts: 9,442 |
Steve Jones Bk4293 Zetec ATX SVT exhaust $125 for exaust shipped, $75 for the install Agreed, nice low growl, but won't wake the neighbors.
|
|
|
|
Joined: Nov 2001
Posts: 637
Veteran CEG\'er
|
Veteran CEG\'er
Joined: Nov 2001
Posts: 637 |
Blake Rosenbaum WannaBe-SVT Zetec ATX Bo-Bo exhaust $145 muffler, $30 resonator removal, JBA Header no cat, $129.00, install = Free. Nice tone, not much drone.
|
|
|
|
Joined: Aug 2001
Posts: 17,248
CEG road warrior
|
CEG road warrior
Joined: Aug 2001
Posts: 17,248 |
Hector Castaneda
Hector
Zetec ATX
Kamikaze race header, 2.5" downpipe to 2.5" flex pipe to 2.5" race cat, 2.25" pipe back to Matrix muffler, no resonator
$640 for parts/$300 for labor
Nice low tone at idle, a lot of rasp at full throttle, will wake up your neighbors a couple of blocks away! I am serious.
If you consider doing a race header make sure you can handle more noise.
Hector
2003 Rally Red Mitsubishi Evolution VIII
257HP/259TQ
2005 Lapis Blue Mazda 6s
RET: 00 Cabernet Red Ford Contour Zetec ATX SUPERCHARGED
160HP/141TQ
|
|
|
|
Joined: Jul 2000
Posts: 3,465
Hard-core CEG'er
|
Hard-core CEG'er
Joined: Jul 2000
Posts: 3,465 |
Joe Hartley ZetecRacing DynoMax Ultraflow in stock res location 2.5" pipe going from flang to the muffler split to dual straight pipes 2.25" with 3" stainless steel tips. some what quiet at idle has a deep tone and just gets louder and louder as you hit the gas. and there is no rasp weather the car is cold or has been warmed up. people that have heard it think I have a perfromance V6 under the hood I got this exaust through a trade with another Contour owner who was looking to make his quieter due to the race headers he has on his duratec all I payed for was labor and a hanger for the second outlet pipe which was $150 to put my exaust on his car and put his on mine.
2003 Subaru WRX some mods
Even if you don't have the answer, you certainly have to admire the problem.
aka ZetecRacing
|
|
|
|
Joined: May 2001
Posts: 2,291
Hard-core CEG'er
|
Hard-core CEG'er
Joined: May 2001
Posts: 2,291 |
Darrel Davis
D Davis
Zetec/MTX
SVT Exhaust w/ resonators still on
$75 for exhaust (not cut/from local CEGer) - six pack of beer for install by StreetFlight.
Very subdued at idle and when casually rowing the gears. Really wakes up under hard accelaration and has a very, very nice tone when engine braking. My CAI makes more noise than the exhaust usually
I dynoed the exhaust and lost nothing down low and gained a couple HP throughout the upper revs.
If someone has audio of a Zetec w/ SVT exhaust and no resonators, I'd love to hear it.
|
|
|
|
Joined: Sep 2002
Posts: 1,957
Hard-core CEG'er
|
Hard-core CEG'er
Joined: Sep 2002
Posts: 1,957 |
Julio Patino lsneo se zetec ATX
2.25 mandrel bent pipe with no resonator. The 2.25 pipe starts right after the flex pipe and runs into a flowmaster 40 series muffler.
Muffler $70 installation and pipes $80 Makes a deep sound when on idle, when its cold it will rasp just a bit but the rasp will go away quick. It sounds deep all the time, its not very loud and wont wake your neighbors unless you gun it. Cruising it is not loud at all and will keep cops away from you. If you are looking for a perfect sleeper this is the one for you.
NEED AN SVT REAR BUMPER!!! pm me
|
|
|
|
Joined: Aug 2001
Posts: 1,840
Hard-core CEG'er
|
Hard-core CEG'er
Joined: Aug 2001
Posts: 1,840 |
James Pettengill StolonTour#05 97 Zetec ATX 2.25" mandrel bent pipe after stock resonator. Dualed out behind gas tank, which is straight piped out to 2.5" chrome tips in svt bumper openings. $75 to have stock exhaust removed at resonator and Y'd out to 2 straight pipes w/ chrome tips. Has a nice growl at idle. A tad raspy when extremely cold but once warm has a nice note to it. Not extremely loud unless really getting on it, and really little or no droning at highway speeds. Sound varies when getting on it. Sometimes it's deep and throaty, other times it's just annoying, but what exhaust isn't at times. Also has a nice growl when coming to a stop from speed. Started out to just be something temporary or so I though but it has grown on me to where I think I'll keep it like it is.
|
|
|
|
Joined: Sep 2002
Posts: 472
CEG\'er
|
CEG\'er
Joined: Sep 2002
Posts: 472 |
svt exhaust, stock res removed and magnaflow 4" round res in place, mufflers at a later date,
any thoughts?
96 gl sport, atx, rip at 95k
FDNY 343 remember 9/11
|
|
|
|
Joined: Jan 2001
Posts: 1,025
Hard-core CEG\'er
|
Hard-core CEG\'er
Joined: Jan 2001
Posts: 1,025 |
Colter Marshall
Pollo_loco69
Zetec/ATX
SVT Exhaust with resonator
Exhaust free. Paid $90 for install
Like Darrel said "Very subdued at idle and when casually rowing the gears. Really wakes up under hard accelaration and has a very, very nice tone when engine braking. My CAI makes more noise than the exhaust usually"
-Colter
My Old Car
Current Cars-
1999 Ford Taurus SE 3.0 Duratec
1999 Ford Explorer XLT, my Geocaching car.
|
|
|
|
Joined: May 2001
Posts: 2,291
Hard-core CEG'er
|
Hard-core CEG'er
Joined: May 2001
Posts: 2,291 |
Originally posted by Pollo_loco69: Like Darrel said "Very subdued at idle and when casually rowing the gears. Really wakes up under hard accelaration and has a very, very nice tone when engine braking. My CAI makes more noise than the exhaust usually"
But you don't "row" the gears
|
|
|
|
Joined: Aug 2001
Posts: 17,248
CEG road warrior
|
CEG road warrior
Joined: Aug 2001
Posts: 17,248 |
Originally posted by D Davis: Originally posted by Pollo_loco69: Like Darrel said "Very subdued at idle and when casually rowing the gears. Really wakes up under hard accelaration and has a very, very nice tone when engine braking. My CAI makes more noise than the exhaust usually"
But you don't "row" the gears
Maybe it is an ATX thing.
Hector
2003 Rally Red Mitsubishi Evolution VIII
257HP/259TQ
2005 Lapis Blue Mazda 6s
RET: 00 Cabernet Red Ford Contour Zetec ATX SUPERCHARGED
160HP/141TQ
|
|
|
|
Joined: Sep 2002
Posts: 472
CEG\'er
|
CEG\'er
Joined: Sep 2002
Posts: 472 |
ddmd3216
atx,zetec
stock single pipe to magnaflow res 10425, to svt exhaust
75 for res, 100 for exh, 80 for install
sounds loud at 3500-4000 rpm when i pass daydreamers on street otherwise quiet, louder than what i had but no drone, also sounds good at hiway speed just cruising along
not a bad start, would like to enlarge piping from res forward, maybe a hi flow cat, then better mufflers
96 gl sport, atx, rip at 95k
FDNY 343 remember 9/11
|
|
|
|
Joined: Apr 2002
Posts: 2,483
Hard-core CEG'er
|
Hard-core CEG'er
Joined: Apr 2002
Posts: 2,483 |
MTX Zetec Mandrel bent 2.25" cat back exhaust (flex pipe replaced with larger 2.25" as well) to a Magnaflow muffler with 2.25" exhaust outlet. $185 For parts & labor. Good sound, not raspy & not angry bees. Droany in the mid rpm range.
Frank McCoy aka Mod-deth aka Mid Life Crisis aka SVT Doood aka mcgainer is a SCAM ARTIST
Pre98 Zetec - Some Mods
|
|
|
|
Joined: Nov 2002
Posts: 8,143
Hard-core CEG'er
|
Hard-core CEG'er
Joined: Nov 2002
Posts: 8,143 |
Name: ZetecNinja Board name: JiggaJerry Engine/Tranny: Zetec/MTX Detailed list of your exhaust mod: Everything stock at the moment except for the DTM style muffler Cost/Installation Charge: $70.99 shipped, $40 install Opinion: It gives off a pretty deep sound, everything else is stock still so its not real loud but when I do the rest of the exhaust it will come out nice and deep...no angry bees Misc. Info: Very happy with the muffler so far...2.5" piping on the way hopefully
|
|
|
|
Joined: Oct 2002
Posts: 484
CEG\'er
|
CEG\'er
Joined: Oct 2002
Posts: 484 |
Jigga, i like your muffler. It looks a lot better in the origional picture Do you have pics of it on your car yet...if so PM me or something
|
|
|
|
Joined: Aug 2002
Posts: 648
Veteran CEG\'er
|
Veteran CEG\'er
Joined: Aug 2002
Posts: 648 |
Name: Tom Oliver Board name: One Tan MDer Engine/Tranny: (Zetec VCT/ ATX) Detailed list of your exhaust mod: (2.25" Mandrel bent single pipe with no resonator to Ravin muffler with single 4" tip.) Cost/Installation Charge: $600 for everything Opinion: very deep sound for a 4cyl. when reving hard still sounds deep (no mosquitos)
PRIME-TOUR
You're fired! I write the books here!
~Tom~
|
|
|
|
Joined: Nov 2002
Posts: 8,143
Hard-core CEG'er
|
Hard-core CEG'er
Joined: Nov 2002
Posts: 8,143 |
might be a while til I have pictures...need a digi cam
|
|
|
|
Joined: Oct 2002
Posts: 484
CEG\'er
|
CEG\'er
Joined: Oct 2002
Posts: 484 |
Let me know when you get them...I can't wait to see how it turned out
|
|
|
|
Joined: Mar 2002
Posts: 2,094
Hard-core CEG'er
|
Hard-core CEG'er
Joined: Mar 2002
Posts: 2,094 |
Heather D. LocoChick'95 ATX Zetec SVT Exhaust w/resonator $90 for exhaust/$85 for install I'm happy with it even though it won't wake the neighbors.
'95 GL White
I've got mods.
|
|
|
|
Joined: Aug 2001
Posts: 17,248
CEG road warrior
|
CEG road warrior
Joined: Aug 2001
Posts: 17,248 |
Originally posted by LocoChick'95: Heather D. LocoChick'95 ATX Zetec SVT Exhaust w/resonator $90 for exhaust/$85 for install I'm happy with it even though it won't wake the neighbors.
About time you put the exhaust on.
Hector
2003 Rally Red Mitsubishi Evolution VIII
257HP/259TQ
2005 Lapis Blue Mazda 6s
RET: 00 Cabernet Red Ford Contour Zetec ATX SUPERCHARGED
160HP/141TQ
|
|
|
|
Joined: Mar 2002
Posts: 2,094
Hard-core CEG'er
|
Hard-core CEG'er
Joined: Mar 2002
Posts: 2,094 |
Originally posted by LoCoZ2.0: Originally posted by LocoChick'95: Heather D. LocoChick'95 ATX Zetec SVT Exhaust w/resonator $90 for exhaust/$85 for install I'm happy with it even though it won't wake the neighbors.
About time you put the exhaust on.
Aww, now you see. Yeah, it took awhile, but it is ON.
'95 GL White
I've got mods.
|
|
|
|
Joined: Oct 2001
Posts: 569
Veteran CEG\'er
|
Veteran CEG\'er
Joined: Oct 2001
Posts: 569 |
Brad Pollock Locster Zetec ATX SVT exhaust (intact) 125 for the exhaust; 70 install Sounds sweet like the others said.
....Brad
Your mom thinks I'm hot!! But my wife rocks!!
99 Mestique Zetec ATX, 96 4Runner 5speed
Mods? Um gotem.
VFA-94VFA-122 VFA-115
|
|
|
|
Joined: May 2003
Posts: 5,621
Hard-core CEG'er
|
Hard-core CEG'er
Joined: May 2003
Posts: 5,621 |
ATX... still got a factory one but looking to replace it - what would ya folks recommend? I reckon that most of the exhaust systems available for Contours are for Duratech... Is that rite?
|
|
|
|
Joined: Aug 2001
Posts: 17,248
CEG road warrior
|
CEG road warrior
Joined: Aug 2001
Posts: 17,248 |
Originally posted by RGSOUNDF: ATX... still got a factory one but looking to replace it - what would ya folks recommend? I reckon that most of the exhaust systems available for Contours are for Duratech... Is that rite?
Get a used SVT exhaust. You can find some in the classifieds.
Hector
2003 Rally Red Mitsubishi Evolution VIII
257HP/259TQ
2005 Lapis Blue Mazda 6s
RET: 00 Cabernet Red Ford Contour Zetec ATX SUPERCHARGED
160HP/141TQ
|
|
|
|
Joined: May 2003
Posts: 5,621
Hard-core CEG'er
|
Hard-core CEG'er
Joined: May 2003
Posts: 5,621 |
OKKI "looking for SVT exhausts"
|
|
|
|
Joined: Jun 2002
Posts: 304
CEG\'er
|
CEG\'er
Joined: Jun 2002
Posts: 304 |
Sean McDonald SMcD Zetec ATX SVT exhaust (intact) $100 parts, $65 labor for install
"And in the lonely cool before dawn, you hear their Zetecs roaring on. When you get to the porch they're gone on the wind......"
(with apologies to the Boss)
I'm here for a good time, not a long time.
'96 GL Zetec ATX (R.I.P.)
'86 Mustang LX ragtop
(wants to be 5.0 when it grows up)
'96 Dodge Stratus
'95 Mercury Sable wagon
|
|
|
|
Joined: Apr 2003
Posts: 1,085
Hard-core CEG\'er
|
Hard-core CEG\'er
Joined: Apr 2003
Posts: 1,085 |
Board name:WestCoastAjax Engine/Tranny: Zetec MTX Detailed list of your exhaust mod: Brullen 2.25 Mandrel bent with Resonator & Muffler(quiet style) Cost/Installation Charge: 795.00 CDN parts only Opinion: Deep sound throughout RPM range. Quiet! More Sports Car sound than Tuner Car sound. Misc. Info: Easy DIY in One hour including jacking the car up, removing old system, installing new and putting the car back down. Comes in Black. Fits all stock mounts.
2012 Lotus Evora
---------
95 Mystique MTX - GONE 395,000 Kms
--------- Both Zetecs
'97 Contour Mtx - stock - GONE
|
|
|
|
Joined: Aug 2001
Posts: 17,248
CEG road warrior
|
CEG road warrior
Joined: Aug 2001
Posts: 17,248 |
Update....I have a Flowmaster 40 series muffler....still LOUD!
Hector
2003 Rally Red Mitsubishi Evolution VIII
257HP/259TQ
2005 Lapis Blue Mazda 6s
RET: 00 Cabernet Red Ford Contour Zetec ATX SUPERCHARGED
160HP/141TQ
|
|
|
|
Joined: Jun 2003
Posts: 20
New CEG\'er
|
New CEG\'er
Joined: Jun 2003
Posts: 20 |
well hmm i have a skunk 2 exhaust cost 190 install was 160 very pleased i believe they took my cat completely out so ok
|
|
|
|
Joined: Jun 2002
Posts: 20
New CEG\'er
|
New CEG\'er
Joined: Jun 2002
Posts: 20 |
First off I'm back on after some how losing my user information but anyway.
I've got the SVT exhaust no resonator I can see gains in sound as well as HP and Torque 96 Mystique ATX Costs $100 exhaust $40 to install
Pacific Green 96 Mystique
17" TSW Wheels Nitto Tires
Sony Xplod System (the new G5 series)
SVT Exhaust minus the Resonator
Eibach Lowering Springs
|
|
|
|
Joined: Aug 2002
Posts: 126
CEG\'er
|
CEG\'er
Joined: Aug 2002
Posts: 126 |
Duratec Local muffler shop. Aprox $325. 2.5" pipe starting after flex. Custom y-pipe just before fuel tank. Splits to two small glass packs and then very nice large tips. Was too loud so I put a third large inline resognater ater the cat, before the fuel tank. Starts/idles very nice. Sounds great in the car, especially when revving. I found, however, that it only sounds good when you are inside the car, probably due to induction (giant AFE cone filter, no air box). When wifey drives it down the strett and gases it, it sounds just a tad ricey and I don't like that. Maybe I'm crazy, but I really wanted it to sound just like a stock Mustang GT!!! Also, in low RPMs, like 1,200, under heavy load (stupid ATX), the drone can still be somewhat loud even with third large glass pack resognator (stock resognator removed).
|
|
|
|
Joined: Aug 2003
Posts: 10
New CEG\'er
|
New CEG\'er
Joined: Aug 2003
Posts: 10 |
where can i find this exhaust system at
|
|
|
|
Joined: Aug 2001
Posts: 17,248
CEG road warrior
|
CEG road warrior
Joined: Aug 2001
Posts: 17,248 |
Another update: Dynomax ultraflow in resonator location....no muffler at the rear of car. Nice and quiet at idle and cruising...get on it...the loudest Zetec out there!
Hector
2003 Rally Red Mitsubishi Evolution VIII
257HP/259TQ
2005 Lapis Blue Mazda 6s
RET: 00 Cabernet Red Ford Contour Zetec ATX SUPERCHARGED
160HP/141TQ
|
|
|
|
Joined: May 2002
Posts: 21,653
I have no life
|
I have no life
Joined: May 2002
Posts: 21,653 |
<<No resonator and no muffler,, pretty loud and decent performance/cost ratio.
98.5 SVT
91 Escort GT (almost sold)
96 ATX Zetec (i brake to watch you swerve)
FS: SVT rear sway bar
WTB: Very cheap beater
CEG Dragon Run - October 13-15
|
|
|
|
Joined: Sep 2003
Posts: 76
CEG\'er
|
CEG\'er
Joined: Sep 2003
Posts: 76 |
I have the same exhaust almost my can is slightly different but I love it to death sounds awsome when the car is modified and looks great from behind.
REDLINING IT ALL THE TIME
1998 mtx zetec contour
17.1 @79mph
open element air filter
ford 9mm racing wires
dtm style exhaust
|
|
|
|
Joined: Apr 2002
Posts: 36
New CEG\'er
|
New CEG\'er
Joined: Apr 2002
Posts: 36 |
I went to my local muffler shop and got 2.25 pipe put on in place of resonater, and then all the way to the back into a magnaflow muffler. Nice sound, not loud at all but has a little growl, can feel it nicly when going around a corner.
-------------------
'95 Contour ZETEC
Tinted Windows(35%)
door dings removed
16" Dubs!
2.25 pipe flowin to a magnaflow
(soon to get CTA intake)
|
|
|
|
Joined: Jan 2003
Posts: 808
Veteran CEG\'er
|
Veteran CEG\'er
Joined: Jan 2003
Posts: 808 |
Brandon Obsidian Zetec ATX Nothing really. Used to have no muffler. That was a little nice. Sounded like crap when it was idling or coming down while placed in a gear. Now I have a Type RS muffler (It is really good! I promise) which can be Fairly loud when needed. Nice and loud when WOT (Intake is still louder... intake is REALLY loud) and it is deep. Not ricey AT ALL. Cost was 60 bucks for the muffler off e-bay and 77 tohave it installed. I had about 5 feet of 2.25 of new exhaust put on.
95 Mystique GS Zetec ATX: Dead - Dec 5th, 2003
94 Accord LX 2.2L MTX Non-Vtec. Few bolt ons.
02 Escape XLT 3.0 V6 ATX. This thing has the CD4E in it?! What the hell was ford thinking?
|
|
|
|
Joined: Apr 2001
Posts: 9,442
Addicted CEG\'er
|
Addicted CEG\'er
Joined: Apr 2001
Posts: 9,442 |
Originally posted by bk4293: Steve Jones Bk4293 Zetec ATX SVT exhaust $125 for exaust shipped, $75 for the install Agreed, nice low growl, but won't wake the neighbors.
Here's the newest video... http://www.ameritech.net/users/bk4293/MVI_0304.avi
|
|
|
|
Joined: Nov 2002
Posts: 8,143
Hard-core CEG'er
|
Hard-core CEG'er
Joined: Nov 2002
Posts: 8,143 |
Originally posted by tourman113: Let me know when you get them...I can't wait to see how it turned out
|
|
|
|
Joined: Aug 2001
Posts: 17,248
CEG road warrior
|
CEG road warrior
Joined: Aug 2001
Posts: 17,248 |
Another addition: Magnaflow muffler
Hector
2003 Rally Red Mitsubishi Evolution VIII
257HP/259TQ
2005 Lapis Blue Mazda 6s
RET: 00 Cabernet Red Ford Contour Zetec ATX SUPERCHARGED
160HP/141TQ
|
|
|
|
Joined: Apr 2001
Posts: 5,975
Hard-core CEG'er
|
Hard-core CEG'er
Joined: Apr 2001
Posts: 5,975 |
Engine/Tranny: SVT V6/MTX Ehaust mod: SHM long tube headers -> Edelbrock -> Bassani Cost/Installation Charge: SHM longtube headers - $1200 Edelbrock muffler - $100 Bassani - $600 Install - $400 Opinion: No rasp or drone thanks to the Edelbrock. Sounds pretty good - should sound better when I go true duals.
|
|
|
|
Joined: Aug 2001
Posts: 17,248
CEG road warrior
|
CEG road warrior
Joined: Aug 2001
Posts: 17,248 |
Whew....wrong forum!
Hector
2003 Rally Red Mitsubishi Evolution VIII
257HP/259TQ
2005 Lapis Blue Mazda 6s
RET: 00 Cabernet Red Ford Contour Zetec ATX SUPERCHARGED
160HP/141TQ
|
|
|
|
Joined: Nov 2002
Posts: 8,143
Hard-core CEG'er
|
Hard-core CEG'er
Joined: Nov 2002
Posts: 8,143 |
update:
No rear muffler or resonator
Recommendation: DON'T do it, sounds horrible
|
|
|
|
Joined: Nov 2001
Posts: 58
CEG\'er
|
CEG\'er
Joined: Nov 2001
Posts: 58 |
1995 Contour w/ no rear muffler. Supposedly sounds like a bong! LOL! I like my exhaust loud, sooo... center resonator will be removed. The cheapest thing I've done to this car is the exhaust. 20 bucks altogether. I get quite a few compliments.
Orange City, FL 1995 Contour GL, Zetec, 5spd., Otto Racing Bomb Racing Muffler, V-Racing Aluminum Wing, PCP Intake w/ Adapter, Spinner Hubcaps (yes, really.) Hopefully, new rims soon!
|
|
|
|
Joined: Jan 2002
Posts: 1,444
Hard-core CEG\'er
|
Hard-core CEG\'er
Joined: Jan 2002
Posts: 1,444 |
Name:Vincent Oliveros Board name: Batmobile Engine/Tranny: Zetec/ATX Detailed list of your exhaust mod: Removed Resonator and HP Racing M18 Cost/Installation Charge: Muffler- $109 shipped Install- $40. Resonator Removal: $20 Opinion: It sounds better than stock, that's for sure. Misc. Info: Got the muffler off ebay and the shop that did all the work was Performance Muffler in Norman Oklahoma. Muffler Picture:
|
|
|
|
Joined: Mar 2003
Posts: 7,117
Hard-core CEG'er
|
Hard-core CEG'er
Joined: Mar 2003
Posts: 7,117 |
This will be GREAT!! But this thread has been around for some time now & I have not seen any links to a sound clip database or web page.
Obviously, there will be separate listings for I-4 & V-6 cars. Would it be a waste of time to further delineate single Vs dual exhaust exit categories?
I also suggest that we standardize the recording location (6" behind the driver side tail light) so all clips can be compared directly.
So, any collection of files yet?
Must be that jumbly-wumbly thing happening again.
|
|
|
|
Joined: Nov 2002
Posts: 8,143
Hard-core CEG'er
|
Hard-core CEG'er
Joined: Nov 2002
Posts: 8,143 |
UPDATE: Possibly the final exhaust mod for this zetec. SVT Exhaust w/ stock resonator and rear mufflers replaced with straight pipe. IMO fairly quiet, no rasp and cannot be heard over the CTA intake. I give it a thumbs up, looks nice too.
|
|
|
|
Joined: Aug 2001
Posts: 17,248
CEG road warrior
|
CEG road warrior
Joined: Aug 2001
Posts: 17,248 |
UPDATE: 2.5" from cat back.
Hector
2003 Rally Red Mitsubishi Evolution VIII
257HP/259TQ
2005 Lapis Blue Mazda 6s
RET: 00 Cabernet Red Ford Contour Zetec ATX SUPERCHARGED
160HP/141TQ
|
|
|
|
Joined: Feb 2003
Posts: 2,975
Hard-core CEG\'er
|
Hard-core CEG\'er
Joined: Feb 2003
Posts: 2,975 |
Originally posted by TourDeForce: This will be GREAT!! But this thread has been around for some time now & I have not seen any links to a sound clip database or web page.
So, any collection of files yet?
I have a sound clip of my CTA stock exhaust. But it's big-ish 40 MB and I don't know how to shorten it.
1992 Ford Escort LX-E
-Tracer LTS spoiler
-GT Grille
|
|
|
|
Joined: Dec 2002
Posts: 205
CEG\'er
|
CEG\'er
Joined: Dec 2002
Posts: 205 |
compress it into an MP3... what format is it now? If you have MSN messenger or AOL instant messenger, you could send it to me and I'll do it for you if you like.
Last edited by jason732; 03/21/04 07:40 PM.
92 Talon TSi AWD
DSM= Daily Scheduled Maintenence
|
|
|
|
Joined: Feb 2003
Posts: 2,975
Hard-core CEG\'er
|
Hard-core CEG\'er
Joined: Feb 2003
Posts: 2,975 |
It's a Video clip with no video only sound. Type of file....I checked, all it said was Video File, and it opens with WMP. Could I Winzip it? I don't know how to Mp3 it.
1992 Ford Escort LX-E
-Tracer LTS spoiler
-GT Grille
|
|
|
|
Joined: Dec 2002
Posts: 205
CEG\'er
|
CEG\'er
Joined: Dec 2002
Posts: 205 |
If you could zip it, I could run it through my video editing software and pull the audio track out, then convert it to MP3. That's the only way to get it to a native audio format at this point. The file sounds like it's an MPEG-1, but that's a good thing for pulling the audio off...
92 Talon TSi AWD
DSM= Daily Scheduled Maintenence
|
|
|
|
Joined: Dec 2002
Posts: 205
CEG\'er
|
CEG\'er
Joined: Dec 2002
Posts: 205 |
Name: Jason
Board name: jason732
Engine/Tranny: Zetec MTX
Detailed list of your exhaust mod: 2.25" Mandrel bent single pipe with no res from flexpipe to a Magnaflow rear muffler and 2.25" turndown tip.
Cost/Installation Charge: $230 installed.
Opinion: At idle, it sounds almost stock. At moderate throttle it's definately louder than stock. At WOT, it's a helluva lot louder than stock. Just cruizing around the grocery store parking lot, you could tell it was louder, but not obnoxious. It won't take any trophies for loudness, but it's got a mellow, deep and even tone with a little rasp when cold, but that's it. Even on the freeway at +/- 75 there's no drone.
Misc. Info: If you want a nice, mellow sounding exhaust that's not going to get you a ticket, this is it. I'm very impressed with the increase in the low end torque I've gained and I wouldn't have it any other way. It's loud when I want it to be, but quiet when I need it to be. I had a guy standing next to the car when I first started it and he said "You just had exhaust work done?" then I floored it, and then it floored him. His expression was priceless. Something like:
92 Talon TSi AWD
DSM= Daily Scheduled Maintenence
|
|
|
|
Joined: Jun 2003
Posts: 389
CEG\'er
|
CEG\'er
Joined: Jun 2003
Posts: 389 |
Originally posted by LoCoZ: UPDATE: 2.5" from cat back.
How does that sound now?
99 Contour SE
-Front oval mesh grille
-tinted windows
Future:
Custom exhaust
CTA intake.
thats pretty much it
|
|
|
|
Joined: Dec 2003
Posts: 1,899
Hard-core CEG\'er
|
Hard-core CEG\'er
Joined: Dec 2003
Posts: 1,899 |
name- Mark L. 1999 contour se atx terminator muffler - 50 dollars resonator removal - 20 dollars sounds like a stock V8 at idle... i am not kidding... acceleration is a bit different tho.. it sounds like a mazda
|
|
|
|
Joined: Apr 2003
Posts: 242
CEG\'er
|
CEG\'er
Joined: Apr 2003
Posts: 242 |
Tony Archer 4banganda5spd '96 Zetec MTX 2.25" aluminized pipe from after flex pipe back to aluminized Flowmaster 40 series Delta Flow muffler in stock muffler location, no resonator. $57 for muffler $10 shipping $275 for pipe and installation very deep at idle with slight burble. smooth, healthy, agressive sound while accelerating. no angry bees or rice rocket cans. deceleration in gear creates a deep resonation in and outside of the car with no popping or undesirable noises. just slightly louder than stock while cruising with no droning,.. very livable. will rasp a little initially after start up for a short time if engine is cold, but will go away quickly as motor warms. overall a very clean, sporty sound, from a system that provides much improved flow resulting in more horsepower, torque, and fun.
|
|
|
|
Joined: Apr 2003
Posts: 242
CEG\'er
|
CEG\'er
Joined: Apr 2003
Posts: 242 |
|
|
|
|
Joined: May 2002
Posts: 21,653
I have no life
|
I have no life
Joined: May 2002
Posts: 21,653 |
Dynomax Ultraflow with 2.25" piping ~$65 for muffler $85 for install Good sound, waiting for it to get louder as it settles in.
98.5 SVT
91 Escort GT (almost sold)
96 ATX Zetec (i brake to watch you swerve)
FS: SVT rear sway bar
WTB: Very cheap beater
CEG Dragon Run - October 13-15
|
|
|
|
Joined: Jun 2003
Posts: 748
Veteran CEG\'er
|
Veteran CEG\'er
Joined: Jun 2003
Posts: 748 |
I have a question for you guys, What would a I-4 sound like with no resonater and mufflers? I am contemplating that or a full exhaust...
STeve
Steven. L. Benthal Jr.
98 Mystique: Meshed Grille & Pioneer Sound System
|
|
|
|
Joined: Aug 2001
Posts: 17,248
CEG road warrior
|
CEG road warrior
Joined: Aug 2001
Posts: 17,248 |
Do a high flow resonator and no mufflers.
Hector
2003 Rally Red Mitsubishi Evolution VIII
257HP/259TQ
2005 Lapis Blue Mazda 6s
RET: 00 Cabernet Red Ford Contour Zetec ATX SUPERCHARGED
160HP/141TQ
|
|
|
|
Joined: Jun 2003
Posts: 748
Veteran CEG\'er
|
Veteran CEG\'er
Joined: Jun 2003
Posts: 748 |
Oooops... i meant an SVT exhaust
Steven. L. Benthal Jr.
98 Mystique: Meshed Grille & Pioneer Sound System
|
|
|
|
Joined: Jun 2003
Posts: 748
Veteran CEG\'er
|
Veteran CEG\'er
Joined: Jun 2003
Posts: 748 |
What would an SVT exhaust sound like without the resonater but with the mufflers.
Steve
Steven. L. Benthal Jr.
98 Mystique: Meshed Grille & Pioneer Sound System
|
|
|
|
Joined: Nov 2003
Posts: 194
CEG\'er
|
CEG\'er
Joined: Nov 2003
Posts: 194 |
First: Scrapped everything from rez back and upped pipe to 2�¼. Then y"d off at next to last bend and on back to 2 nice chrome angle cut with rolled edges tips. looks great but too loud. Second: replaced rez with glasspack. Better but still to loud for me. Third: Added mini GP's just before the tips. Now we're getting somewhere, it's much more better although I'm thinking about replacing the mid GP with a Cherry Bomb twin tube GP. They say it gives you the performance of a GP but the quite of a turbo muffler $'s: Don't ask!
Sarge43
"00" Tique 2.0L I4 ATX
"98" Mustang 3.8L V6 AT
The reason there's so much ignorance is that those who have it are so eager to share it.
|
|
|
|
Joined: Jan 2005
Posts: 16
New CEG\'er
|
New CEG\'er
Joined: Jan 2005
Posts: 16 |
Yeh i have a ? about cutting out the resinator. Do i need 2.25 ID or OD pipe and how long should i get it. Another ?, weld it or clamp it. I work for AutoZone, so parts are CHEAP for me. Thanx
how slow can you go?!
1999 Mercury Mystique GS Tan
99% Stock
0-60 @ 10.9
1/4 @ 17.85 & 76 MPH
Top Speed 105 MPH (Governed)
Visit my web site @ http://clik.to/jimmydean
|
|
|
|
Joined: May 2000
Posts: 3,335
Hard-core CEG'er
|
Hard-core CEG'er
Joined: May 2000
Posts: 3,335 |
Engine/Tranny: Zetec MTX
Detailed list of your exhaust mod:Mystery mod, SVT exhaust, with aftermarket resonator (cant remember brand) with polished Magnaflows (were on the exhaust when I bought it) running into ~3.5" tips.
Cost/Installation Charge: <$150
Opinion: Quiet at idle. The vibrations from the (4) poly motors mounts make more noise then the exhaust puts off. Interior drone is there, especially at 3500 RPMs and when shifting. Again I believe this is due to the mounts and not the exhaust. Up into the RPMs it has somewhat of a ricey sound, but a lot deeper. Im happy with it.
Misc. Info: I doubt its going to be calling the cops to come get me, but if I was in a quiet neighborhood and someone had their windows open, they would hear me. Cant judge power differences as it was installed when I did my ATX/MTX swap.
· Jon Miconi
· Coming Soon!
· 01 Cougar
· 98 V70R
|
|
|
|
Joined: Dec 2004
Posts: 333
CEG\'er
|
CEG\'er
Joined: Dec 2004
Posts: 333 |
Engine/Tranny: zetec/atx Detailed list of exhaust or mod:Flowmaster turbo muffler installed @ local exhaust shop W/chrome down tip, all else stock. Cost/Installation: $64 total. Opinion: Sounds a bit louder than stock when driving normal, half thottle, a bit louder, WOT, really loud. Misc. info:Catches people at the track by supprise everytime. When down RPMs, has a slight wine. Really good, suggested. Im about to remove the res and go w/the 2.25" piping and see what happens.
|
|
|
|
Joined: Mar 2005
Posts: 82
CEG\'er
|
CEG\'er
Joined: Mar 2005
Posts: 82 |
he i have a 96 mystique with the rear muffler cut out and the rest is stock..it was realy quite but then i think the resonater blew out or something cause man its loud now..but only at certain points..if i have it har don throttle it isnt to bad sounds like a truck ahha serioulsy it does and when i down shift lets say to second gear at 60 kmh which is at 4000 it has a cool vibration sound and man it echoes off of buildings sucha unique sound to it..but i was thinking of putting a glass pack in place fo the resonter or a jsut a straight through smaller resonater into a magnaflow aluminized wiht 1 3/4 in and 1 3/4 out jsut so that it will have that sotck look ahah i dont want ot give anyhting away here for them civc guys haha so what do u guys think ? will it sound nice..or maybe shoul si jsut put a straight pipe in place of the resonater and that magnaflow muffler at the rear give me some ideas guys..i want a loud car under throttle something to scare people aahh casue around here cops dotn care...
|
|
|
|
Joined: May 2002
Posts: 21,653
I have no life
|
I have no life
Joined: May 2002
Posts: 21,653 |
Originally posted by mystiqueness: i want a loud car under throttle something to scare people aahh casue around here cops dotn care...
I hate people too.
header (www.zxtuner.com), 2.5" backerds, magnerflow resomonator in middle, dynomazimer muffler at back. Mandrell bit.
98.5 SVT
91 Escort GT (almost sold)
96 ATX Zetec (i brake to watch you swerve)
FS: SVT rear sway bar
WTB: Very cheap beater
CEG Dragon Run - October 13-15
|
|
|
|
Joined: Mar 2005
Posts: 82
CEG\'er
|
CEG\'er
Joined: Mar 2005
Posts: 82 |
i had a post before when my name was mystiqueness who just had a cut off muffler at back..i got an update now and i have a cherrybomb placed in the middle where the resonater sat fyi a cherry bomb is jsut a glass pack.it doesnt sound to bad it is a bit quiter than before but still sounds good when u come onto it..
|
|
|
|
Joined: Mar 2003
Posts: 42
New CEG\'er
|
New CEG\'er
Joined: Mar 2003
Posts: 42 |
i have a cat back piper stainless steel system very good built looks good sounds ace too ,not to loud at 70mph crusing and a nice roar when floor and a nice burble on tick over and a good price to $300 dollars roughly and �£280 sterlin and loads of tips/trims to pick and duel system exits too
rs body kit
2.0 tb bomz kit
piper exhaust 3.5"
megaleads ht
16" cossie rims
Meg sticker
ghia maplight/passager rear light
ice
under bonnet bling
Auto wiper in reverse the first Mk1
windows on mod with ignition off
|
|
|
|
Joined: Nov 2003
Posts: 1,831
Hard-core CEG\'er
|
Hard-core CEG\'er
Joined: Nov 2003
Posts: 1,831 |
Kyle Blindauer 99contourdriver 99 Contour SE Zetec ATX SVT exhaust: $125.00 Cut off stock exhaust, weld on SVT exhaust...done by shop: $135.00 2" Stock Flexpipe to 2.25" SVT duals w/no resonator Little rasp on cool mornings for about 10 min. till warms up, but sounds AWESOME!! Doesn't sound like a ricer, but still makes some noise for a 4 cyl! I am very happy with it! Doesn't wake the neighbors, but still sounds great!
A Contour is not just a car, it's an experience
99 T-Red SE Zetec ATX
Born April 16, 1999
98 E0 Silver Frost CSVT
#3175/3565
Born August 21st, 1997
Stored at P.R.T. for the winter
67 Mustang 289 project car
|
|
|
|
Joined: Apr 2003
Posts: 1,085
Hard-core CEG\'er
|
Hard-core CEG\'er
Joined: Apr 2003
Posts: 1,085 |
Originally posted by WestCoastAjax: Board name:WestCoastAjax Engine/Tranny: Zetec MTX Detailed list of your exhaust mod: Brullen 2.25 Mandrel bent with Resonator & Muffler(quiet style) Cost/Installation Charge: 795.00 CDN parts only Opinion: Deep sound throughout RPM range. Quiet! More Sports Car sound than Tuner Car sound. Misc. Info: Easy DIY in One hour including jacking the car up, removing old system, installing new and putting the car back down. Comes in Black. Fits all stock mounts.
UPDATE: Kamikazi Shorty header-Ceramic coated 225 + 125 Custom made 2.5" downpipe with Stainless Steal flex pipe - 2.5" I.D., made from supplied pipe -Ceramic Coated 80 Now its sounds like a Sports Car!
2012 Lotus Evora
---------
95 Mystique MTX - GONE 395,000 Kms
--------- Both Zetecs
'97 Contour Mtx - stock - GONE
|
|
|
|
Joined: Jun 2004
Posts: 1,287
Hard-core CEG\'er
|
Hard-core CEG\'er
Joined: Jun 2004
Posts: 1,287 |
Chris Koromvokis 98 Contour Gl Zetec Atx Custom 2.5 full exhaust. No resonater HP Racing (High Performance Racing) Canister Very loud. will wake up nieighboors Had headers but to many cels.....
|
|
|
|
Joined: Apr 2005
Posts: 179
CEG\'er
|
CEG\'er
Joined: Apr 2005
Posts: 179 |
Zetec ATX. Focus 4into1 stainless shortie header. Cat removed. Runs into 2.5" stainless pipe(instead of cat) for 1 foot. Drops to 1 7/8" makes a hard right and goes for 6 inches and goes straight back to stock flex pipe. stock exhaust till pipe turns to go straight back to bumper (removed secondary muffler) and installed a 2" cherrybomb with a center exit exhaust. Nice low tone at idle and nice mellow tone cruising. When you get on it, it does blat a bit and sounds quite raspy whether or not it is cold or warm. Not the way I would recommend doing an exhaust. Didn't seem to help power at all.
95 Contour, Custom EVO bodykit, 2.0l, PNP Focus head, Stage 2 cams, Je pistons, Eagle rods, 4in1header, 2.5" header back exhaust(complete stainless), D P nitrous, ram air intake, 10mm wires, flamethrower.
|
|
|
|
Joined: Mar 2005
Posts: 82
CEG\'er
|
CEG\'er
Joined: Mar 2005
Posts: 82 |
Originally posted by WestCoastAjax: Originally posted by WestCoastAjax: Board name:WestCoastAjax Engine/Tranny: Zetec MTX Detailed list of your exhaust mod: Brullen 2.25 Mandrel bent with Resonator & Muffler(quiet style) Cost/Installation Charge: 795.00 CDN parts only Opinion: Deep sound throughout RPM range. Quiet! More Sports Car sound than Tuner Car sound. Misc. Info: Easy DIY in One hour including jacking the car up, removing old system, installing new and putting the car back down. Comes in Black. Fits all stock mounts.
UPDATE: Kamikazi Shorty header-Ceramic coated 225 + 125 Custom made 2.5" downpipe with Stainless Steal flex pipe - 2.5" I.D., made from supplied pipe -Ceramic Coated 80 Now its sounds like a Sports Car!
could u feel much more hp with the shorty header i was alwasy wondering if i was to get the obx shorty that connects on the cat if it would a good difference ro if u need to replace that massive cataylic
|
|
|
|
Joined: Apr 2003
Posts: 242
CEG\'er
|
CEG\'er
Joined: Apr 2003
Posts: 242 |
update: gutted cat, louder everywhere. rasps a lot during full throttle and at a couple of rpm points when downshifting to slow while in gear. sounds throaty and burbly at part throttle and putting around. looking to replace flowmaster with off the shelf dynomax super turbo muffler
|
|
|
|
Joined: Apr 2003
Posts: 242
CEG\'er
|
CEG\'er
Joined: Apr 2003
Posts: 242 |
dynomax on with 4" chrome rolled tip slant cut. sounds real good! deeper, sportier sound. rasp is gone unless reving it high in nuetral yet still a performance tone to it. very happy.
|
|
|
|
Joined: Jan 2005
Posts: 261
CEG\'er
|
CEG\'er
Joined: Jan 2005
Posts: 261 |
the other davis caleb 2.0 Zetec Contour GL SVT Exhaust minus mufflers Sound: decent, not too ricey good rumble, but almost non-existant when idling at a light
-Contour's dead, but is being revived...
Originally posted by CSVT1214: Originally posted by ford zetec2: after than, what do i do with the 98 short shifter? do I place it in there like it is?
Stick it in your butt and rotate.
|
|
|
|
Joined: Aug 2005
Posts: 126
CEG\'er
|
CEG\'er
Joined: Aug 2005
Posts: 126 |
anybody actually use a 1 3/4 dynomax or do you step it up to 2 inch? i work at napa, i can actually get the 2 inch for $35
99 Contour LX MTX, Cone Air Filter, Custom Grille
95 Neon ATX Intake, Ractive Muffler, Green Painted valve cover, fuel rail, and intake, b/w painted interior, white exterior trim, shaded tail lights
|
|
|
|
Joined: Sep 2003
Posts: 147
CEG\'er
|
CEG\'er
Joined: Sep 2003
Posts: 147 |
y split before the mufflers. No resonator, Thrush Turbo Mufflers, Cheap tips from the car store........
Nice little rumble, not ricey, nice when starting up or driving on the freeway. A little rasp when you go WOT.
|
|
|
|
Joined: Aug 2005
Posts: 126
CEG\'er
|
CEG\'er
Joined: Aug 2005
Posts: 126 |
I can get the thrush turbo mufflers for $19
99 Contour LX MTX, Cone Air Filter, Custom Grille
95 Neon ATX Intake, Ractive Muffler, Green Painted valve cover, fuel rail, and intake, b/w painted interior, white exterior trim, shaded tail lights
|
|
|
|
Joined: Aug 2000
Posts: 8,301
Addicted CEG\'er
|
Addicted CEG\'er
Joined: Aug 2000
Posts: 8,301 |
$21 shipped for my Summit racing turbo muffler. Its in place of the resonator with no rear muffler on stock pipe. Nice sound, kind of deep.
-Ken V.
1998.5 SE Praire Tan Zetec ATX
psycho_bass@hotmail.com
Roush springs Roush rear sway bar BAT struts 17" Millie Miglia HT3 and a ton of subtle asthetic mods
|
|
|
|
Joined: Jan 2005
Posts: 261
CEG\'er
|
CEG\'er
Joined: Jan 2005
Posts: 261 |
Originally posted by the other davis: the other davis caleb 2.0 Zetec Contour GL SVT Exhaust minus mufflers Sound: decent, not too ricey good rumble, but almost non-existant when idling at a light
put the mufflers back on and it's all welded up and sounds great.
-Contour's dead, but is being revived...
Originally posted by CSVT1214: Originally posted by ford zetec2: after than, what do i do with the 98 short shifter? do I place it in there like it is?
Stick it in your butt and rotate.
|
|
|
|
Joined: Jan 2006
Posts: 46
New CEG\'er
|
New CEG\'er
Joined: Jan 2006
Posts: 46 |
Does anyone know if the Focus Headers for the zetec will bolt on to the contour zetec?
|
|
|
|
Joined: Aug 2001
Posts: 17,248
CEG road warrior
|
CEG road warrior
Joined: Aug 2001
Posts: 17,248 |
Originally posted by chriseichman: Does anyone know if the Focus Headers for the zetec will bolt on to the contour zetec?
It will with some modification......search around this forum and you will find some answers.
Hector
2003 Rally Red Mitsubishi Evolution VIII
257HP/259TQ
2005 Lapis Blue Mazda 6s
RET: 00 Cabernet Red Ford Contour Zetec ATX SUPERCHARGED
160HP/141TQ
|
|
|
|
Joined: Jan 2006
Posts: 46
New CEG\'er
|
New CEG\'er
Joined: Jan 2006
Posts: 46 |
thanx I found what I was looking for, but I probably should have read a little more b4 asking, but I appreciate your help.
|
|
|
|
Joined: Sep 2003
Posts: 147
CEG\'er
|
CEG\'er
Joined: Sep 2003
Posts: 147 |
Name: Armin Board name: Engine/Tranny: zetec I4 ATX
Detailed list of your exhaust mod: Custom Mandrel Bend after Gastank. 2.25". Dynomax Magnum Glasspack Muffler in place of the RES. No Mufflers just straight tips.
Cost/Installation Charge: Muffler was 20 from jegs, cost $30 to put muffler on and 80 to put the straight pipes on in place of the mufflers.
Opinion: Nice sound when started. Cold or hot no rasp. Deep sound when normal driving and nice drone when on the freeway......
BTW, What would a dynomax ultra flow sound like in place of the res with no mufflers. Will it be a loud obnoxious sound or will it sound good? Good as in kind of deep nice drone, not that loud of rasp.
|
|
|
|
Joined: Mar 2003
Posts: 49
New CEG\'er
|
New CEG\'er
Joined: Mar 2003
Posts: 49 |
Hello Folks, I am returning to the mod scene. I have a 96 Contour GL-Sport, Zetec MTX. I am looking to perform some serious mods: 1) CTA Intake. 2) Magnecor 8.5 wires, Bosch Platinum +4 plugs, voltage stabilizer. Am considering an Accel CDI ignition as well 2) Brakes. Anyone know of how to convert drum to disc? 3) Strut bars and rear 21mm BAT bar, urethane bushings everywhere 4) Exhaust. Headers and catback 5) Fidanza alum flywheel, Unorthodox U/D pulley 6) Cyl head work, cams, intake manifold matching (to cyl head) I have a bracket from A/C connecting to head, making the shorty Focus header impossible. I like the shorty b/c it allows me to use the stock cat. However, I am looking at long tube headers (4-1, NOT 4-2-1) so that I can increase power. I plan to remove the stock resonator and put the stock cat down in it's current location. Is this a good idea? I want to remain street legal. Thanks, Shamun
96 GL-Sport 2.0L, MTX
Bernardo Bourges' CTA CAI,
Dmitri's SVT E0s rims, 205/55R-16, Dunlop SPs.
|
|
|
|
Joined: Mar 2003
Posts: 7,117
Hard-core CEG'er
|
Hard-core CEG'er
Joined: Mar 2003
Posts: 7,117 |
Originally posted by shamun: I plan to remove the stock resonator and put the stock cat down in it's current location. Is this a good idea? I want to remain street legal.
Just for the proper function of the unit, it might be a little too far downstream at that location. Additionally, you may want to keep the res to quiet the headers, then later on have the option to delete or upgrade to a Magnaflow.
For my daughters Zetec, I added the 4-1 headers and placed a new 'bullet' cat right after the headers. Kept the stock res which I plan to replace with a Magnaflow or similar in the next week or two.
Must be that jumbly-wumbly thing happening again.
|
|
|
|
Joined: Sep 2002
Posts: 456
CEG\'er
|
CEG\'er
Joined: Sep 2002
Posts: 456 |
NAME Mike Jordan
Board Name: supertouringmike
Engine/tranny: Zetec MTX
Exhaust: removed res,stock pipe to rear,Flowmaster 40 with turn down (stock type )tip. Looks Stock.
Sound: slighty throaty at idle, not loud but deep at 100MPH and I've never heard it from the outside (drive by etc) Sorry
01 PORSCHE 996
Merdian/Black
Full Aero
Fabspeed mufflers
Fabspeed CAI
B & M shifter
96 GL MTX Zetec 2.0
White/Blue
Blaupunkdt Houston
K & N Drop in/Koni Kit
18"RageEnduros/Flowmaster 40 Series
|
|
|
|
Joined: Mar 2003
Posts: 49
New CEG\'er
|
New CEG\'er
Joined: Mar 2003
Posts: 49 |
SOrry for the newbie post, please don't flame me! I am looking for an exhaust system for my 96. I recent purchased a Tsudo header from eBay. It is a long-tube 4-1 type, with O2 senson bung. Unfortunately, my current O2 sensor seems to attach to the cat (it looks like it). I am going to purchase a high-flow cat that I wish to place just aft of the header collector. 1) Do you recommend any particular high flow cat (brand, size, flanges (two or three bolt))? 2) I wish to replace the center resonator with a straight pine. Can the stock muffler handle the extra flow? As for install, I sure hope that DanG is up for a project!
Many thanks, Shamun
96 GL-Sport 2.0L, MTX
Bernardo Bourges' CTA CAI,
Dmitri's SVT E0s rims, 205/55R-16, Dunlop SPs.
|
|
|
|
Joined: Aug 2005
Posts: 114
CEG\'er
|
CEG\'er
Joined: Aug 2005
Posts: 114 |
95 mystique zetec atx 2.0" v6 contour pipes (walker) flowmaster delta 60 muffler turn down tip (flat black) not loud, very deep, looks oem
1995 MYSTIQUE 2.0L
-16" SVT wheels
-Custom intake with HKS filter
-audiobahn/pioneer stereo
-Graphite grey met
-Netherlands Plates
|
|
|
|
Joined: May 2006
Posts: 17
New CEG\'er
|
New CEG\'er
Joined: May 2006
Posts: 17 |
2 1/4" pipe from flex back with 5x8 Magnaflow muffler in Resonator location. Exhaust was painted black with a 2.5" slash cut chrome tip at the end. Quiet as stock w/ res cut out but gets louder as your right foot goes down. Nice and mellow sound cruising.
'96 Contour - Zetec/MTX 130+k mi. White/tan
Tints, 2.25" custom magnaflow catback, tach cluster
'86 Mustang SVO Red/Sunroof 80k orig. Needs work
Cone filter, E6 Manifold, '01 16" Pony Wheels
|
|
|
|
Joined: Aug 2005
Posts: 114
CEG\'er
|
CEG\'er
Joined: Aug 2005
Posts: 114 |
Originally posted by ev1lbry4n: 95 mystique zetec atx
2.0" v6 contour pipes (walker) flowmaster delta 60 muffler turn down tip (flat black)
not loud, very deep, looks oem
***EDIT*** i got the new system put on today
2.25" piping Brullen mid muffler and rear muffler Ractive oval tip
sounds like a touring car
1995 MYSTIQUE 2.0L
-16" SVT wheels
-Custom intake with HKS filter
-audiobahn/pioneer stereo
-Graphite grey met
-Netherlands Plates
|
|
|
|
Joined: Apr 2001
Posts: 9,442
Addicted CEG\'er
|
Addicted CEG\'er
Joined: Apr 2001
Posts: 9,442 |
Originally posted by blakjak: the other davis caleb 2.0 Zetec Contour GL SVT Exhaust minus mufflers Sound: decent, not too ricey good rumble, but almost non-existant when idling at a light
Intake????
did you stand outside your car and let someone else drive around?
I got oober compliments with this set-up....see the vids posted earlier.
Steve
|
|
|
|
|