|
|
Joined: Oct 2002
Posts: 76
CEG\'er
|
OP
CEG\'er
Joined: Oct 2002
Posts: 76 |
I use a hydro zetec in a RWD platform. The stock single piece steel manifold shrouds about 20% of the bottom of the port in the header flange. I realise that most of the flow is in the upper reion of the exhaust port. Is there is "big bore" gasket for any Zetec available in the aftermarket? The standard piece will have compromised sealing if modified. TIA.
|
|
|
|
Joined: Oct 2002
Posts: 2,408
Hard-core CEG'er
|
Hard-core CEG'er
Joined: Oct 2002
Posts: 2,408 |
Originally posted by se7en: I use a hydro zetec in a RWD platform.
??????????????????????????????????????????????????????????????????? Might get a better response if you explain! Muffler shop can weld on a different flange, any setup you want.
"Those who cannot remember the past are condemned to repeat it" -George Santayana
|
|
|
|
Joined: Aug 2001
Posts: 17,248
CEG road warrior
|
CEG road warrior
Joined: Aug 2001
Posts: 17,248 |
Hector
2003 Rally Red Mitsubishi Evolution VIII
257HP/259TQ
2005 Lapis Blue Mazda 6s
RET: 00 Cabernet Red Ford Contour Zetec ATX SUPERCHARGED
160HP/141TQ
|
|
|
|
Joined: Aug 2000
Posts: 8,301
Addicted CEG\'er
|
Addicted CEG\'er
Joined: Aug 2000
Posts: 8,301 |
Originally posted by se7en: I use a hydro zetec in a RWD platform.
Call me crazy, is this for a kit car with a Zetec? Last time I checked, my Contour was not RWD
-Ken V.
1998.5 SE Praire Tan Zetec ATX
psycho_bass@hotmail.com
Roush springs Roush rear sway bar BAT struts 17" Millie Miglia HT3 and a ton of subtle asthetic mods
|
|
|
|
Joined: Aug 2001
Posts: 17,248
CEG road warrior
|
CEG road warrior
Joined: Aug 2001
Posts: 17,248 |
Originally posted by CRZYDRVR: Originally posted by se7en: I use a hydro zetec in a RWD platform.
Call me crazy, is this for a kit car with a Zetec? Last time I checked, my Contour was not RWD
I wish it was. I probably could do crazy burnouts.
Hector
2003 Rally Red Mitsubishi Evolution VIII
257HP/259TQ
2005 Lapis Blue Mazda 6s
RET: 00 Cabernet Red Ford Contour Zetec ATX SUPERCHARGED
160HP/141TQ
|
|
|
|
Joined: Aug 2000
Posts: 8,301
Addicted CEG\'er
|
Addicted CEG\'er
Joined: Aug 2000
Posts: 8,301 |
-Ken V.
1998.5 SE Praire Tan Zetec ATX
psycho_bass@hotmail.com
Roush springs Roush rear sway bar BAT struts 17" Millie Miglia HT3 and a ton of subtle asthetic mods
|
|
|
|
Joined: Jul 2000
Posts: 3,465
Hard-core CEG'er
|
Hard-core CEG'er
Joined: Jul 2000
Posts: 3,465 |
Originally posted by CRZYDRVR: Originally posted by se7en: I use a hydro zetec in a RWD platform.
Call me crazy, is this for a kit car with a Zetec? Last time I checked, my Contour was not RWD
ummm it's for his Lotus Seven hence the name... and also I'm unaware of any aftermarket exaust gasket manifold.
2003 Subaru WRX some mods
Even if you don't have the answer, you certainly have to admire the problem.
aka ZetecRacing
|
|
|
|
Joined: Oct 2002
Posts: 76
CEG\'er
|
OP
CEG\'er
Joined: Oct 2002
Posts: 76 |
Ayup. 96 contour block and management into a seven clone. 1450 lb with driver. . So what do you guys with aftermarket headers use then? What do the Focus people use? I realise that the contique platform seems to be underrepresented in the aftermarket.
|
|
|
|
Joined: May 2002
Posts: 21,653
I have no life
|
I have no life
Joined: May 2002
Posts: 21,653 |
98.5 SVT
91 Escort GT (almost sold)
96 ATX Zetec (i brake to watch you swerve)
FS: SVT rear sway bar
WTB: Very cheap beater
CEG Dragon Run - October 13-15
|
|
|
|
Joined: Jul 2000
Posts: 3,465
Hard-core CEG'er
|
Hard-core CEG'er
Joined: Jul 2000
Posts: 3,465 |
2003 Subaru WRX some mods
Even if you don't have the answer, you certainly have to admire the problem.
aka ZetecRacing
|
|
|
|
|
|