|
Joined: May 2001
Posts: 682
Veteran CEG\'er
|
OP
Veteran CEG\'er
Joined: May 2001
Posts: 682 |
Okay, I still haven't managed to measure the exact current drawn by my e-RAM, or the voltage drop in its wiring for that matter, but I have managed to contrive a pressure measurement. And it's putting out way less than advertised.
(Does anybody remember those simple little current meters which consist of a little compass needle on a spring, which would measure the current in battery cables and other heavy wiring just by being held next to it? I can't find one. Don't they still make them?)
I can estimate the current crudely. Running the e-RAM dropped the voltage at the battery terminal by 0.5v, and turning on the headlights dropped it by 0.4v on low beams and 0.55v on high beams. So, the thingy draws less current than the high beams do. I think my bulbs are stock, or close enough, and the Haynes manual gives both high and low beam wattage as 55 per bulb. This leads me to conclude that the e-RAM is drawing more than 110 watts and less than 220. That would be maybe 15 amperes. Given that it's advertised to draw 700 watts or 50 amperes, this is not good.
Now, air pressure. I hooked up a ten foot length of clear vinyl tubing to the valve cover vent attachment nipple on the CTA intake, and made a U-bend in it with water inside. I could then measure the difference in level between the two tubes, which is proportional to the air pressure difference.
I tried it with the engine off, with the engine idling, and with the engine revved to 3000-4000 in neutral. (I had no way to try this while under load, or at any really wide throttle.) The off measurement was 7.5 inches, idle was 9.3 inches, and revved up was a little less, maybe 9.0 inches. I think there was about 0.3 inches of vacuum when revved with the e-RAM off, so I'll go with the figure of 9.3 inches. That makes about 0.35 pounds per square inch, barely more than a third of what was advertised!
I've seen one other guy complain that his e-RAM drew only 15 amps and produced far less than advertised pressure. It looks to me like the company once sold a good fan, and then -- perhaps when the product changed ownership a year or two ago -- they substituted a cheap inferior fan without changing the advertising claims.
Now we'll see if their guarantee is any good.
|
|
|
|
Joined: Jan 2002
Posts: 1,939
Hard-core CEG'er
|
Hard-core CEG'er
Joined: Jan 2002
Posts: 1,939 |
I was hoping it would work out for you.
2000 Silver Frost SVT
# 1637/2150
D.O.B. 01/14/2000
|
|
|
|
Joined: Oct 2000
Posts: 6,760
Hard-core CEG'er
|
Hard-core CEG'er
Joined: Oct 2000
Posts: 6,760 |
maybe you should try the tornado?
Ryan
Trollin!
|
|
|
|
Joined: May 2001
Posts: 682
Veteran CEG\'er
|
OP
Veteran CEG\'er
Joined: May 2001
Posts: 682 |
a picture of my installation:
|
|
|
|
Joined: May 2002
Posts: 21,653
I have no life
|
I have no life
Joined: May 2002
Posts: 21,653 |
nice installation,, those wires are sorta small,,, have u contacted the company,, that really sucks,, hope u figure it out
98.5 SVT
91 Escort GT (almost sold)
96 ATX Zetec (i brake to watch you swerve)
FS: SVT rear sway bar
WTB: Very cheap beater
CEG Dragon Run - October 13-15
|
|
|
|
Joined: Sep 2000
Posts: 9,602
Hard-core CEG'er
|
Hard-core CEG'er
Joined: Sep 2000
Posts: 9,602 |
Any news on if your's was just a fluke???
2000 SVT #674
13.47 @ 102 - All Motor!
It was not broke; Yet I fixed it anyway.
|
|
|
|
Joined: Feb 2001
Posts: 570
Veteran CEG\'er
|
Veteran CEG\'er
Joined: Feb 2001
Posts: 570 |
Nice install...Let us know what happens!
|
|
|
|
Joined: May 2001
Posts: 682
Veteran CEG\'er
|
OP
Veteran CEG\'er
Joined: May 2001
Posts: 682 |
Okay, the guy at e-RAM is having me send in the fan to see if there's something wrong with it. He assures me that the new plastic one is not weaker or cheaper than the old metal one -- he says it's more efficient, in fact. The motor inside, I observed, is a model airplane motor made by Astro Flight, which from what I've been able to glean off the web is considered a high quality product. But I haven't been able to figure out which particular Astro Flight model it is. Might be a 608 or 610, or maybe a 305 or 306 intended for model boats instead of planes.
|
|
|
|
Joined: May 2001
Posts: 682
Veteran CEG\'er
|
OP
Veteran CEG\'er
Joined: May 2001
Posts: 682 |
Originally posted by Paul Kienitz: Might be a 608 or 610, or maybe a 305 or 306 intended for model boats instead of planes.
Turns out it's a 610, a.k.a model FAI-15, with a different custom winding. I'm sending it back now. I notice that there is a scraped spot on the inside where apparently the fan blades rubbed during operation at least once, but I'm pretty sure it was not pinched there in its working install position... or was it? I tried an ohmmeter on it, and the resistance should have been way under one ohm, but it kept coming up as 1.5 ohms. That's not right.
|
|
|
|
Joined: May 2002
Posts: 21,653
I have no life
|
I have no life
Joined: May 2002
Posts: 21,653 |
i thought the e-ram is 700 watts, that airplane motor is 375watts????
98.5 SVT
91 Escort GT (almost sold)
96 ATX Zetec (i brake to watch you swerve)
FS: SVT rear sway bar
WTB: Very cheap beater
CEG Dragon Run - October 13-15
|
|
|
|
|