|
|
Joined: Aug 2002
Posts: 30
New CEG\'er
|
OP
New CEG\'er
Joined: Aug 2002
Posts: 30 |
Did my bearing on 98 contour and it seems that it had the job done previously as the hub side circlip was missing. Where is the best place to buy the circlip in detroit area?
1998 Contour SE
MTX v6 loaded
1996 Mystique GS
ATX 4 cyl
|
|
|
|
Joined: Dec 2001
Posts: 6,910
Hard-core CEG'er
|
Hard-core CEG'er
Joined: Dec 2001
Posts: 6,910 |
there seems to have been a change at some point, our 95s have to snap rings, one on either side of the bearing, the 99s only have one ...
btw we thought the same thing with out 99 until we changed a bearing on my 99 ...
- 95 Mystique LS - Zetec/5spd
- 99 Contour SeVT Sport - Duratec/5spd
Official NE-CEG Contour/Mustang Family
|
|
|
|
Joined: Feb 2004
Posts: 702
Veteran CEG\'er
|
Veteran CEG\'er
Joined: Feb 2004
Posts: 702 |
CSVT E0 3L
14.5 @ 94mph, Stock Intake, Stock Exhaust minus Resonator, CEL, And Broken Pass. Side CV...Untuned.
|
|
|
|
Joined: Dec 2001
Posts: 6,910
Hard-core CEG'er
|
Hard-core CEG'er
Joined: Dec 2001
Posts: 6,910 |
if the bearing is still making noise then there is a good chance that the bearing was pressed in wrong
iirc my father put a second ring in also on the last one since I had some extra hubs lying around, it didn't cause any unusual noises
- 95 Mystique LS - Zetec/5spd
- 99 Contour SeVT Sport - Duratec/5spd
Official NE-CEG Contour/Mustang Family
|
|
|
|
Joined: Aug 2002
Posts: 30
New CEG\'er
|
OP
New CEG\'er
Joined: Aug 2002
Posts: 30 |
Well I put the one that was on the spindle on the hub side as I needed to press the hub in. So I am missing the circlip on the axle side which was the side that it originally was installed on.
Also how much play should you find in the half shaft? Is it possible to pull it out to far? They seem to have slid out during pulling the hub.
Last edited by bgailitis; 06/12/06 09:37 PM.
1998 Contour SE
MTX v6 loaded
1996 Mystique GS
ATX 4 cyl
|
|
|
|
Joined: Feb 2004
Posts: 702
Veteran CEG\'er
|
Veteran CEG\'er
Joined: Feb 2004
Posts: 702 |
Trust Me...Put That Circlip On the Axle Side. If You Still Have A Problem (I.E. Scarred Hub Internally) You'll end Up With Metal Shavings All Over Your ABS Ring And ABS Speed Sensor.
And Yes I Suppose It Is Possible. I Believe It Calls For Somewhere Around The 255-265lbs Of Tq Area. Someone Correct me If I'm Wrong...
CSVT E0 3L
14.5 @ 94mph, Stock Intake, Stock Exhaust minus Resonator, CEL, And Broken Pass. Side CV...Untuned.
|
|
|
|
Joined: Feb 2004
Posts: 702
Veteran CEG\'er
|
Veteran CEG\'er
Joined: Feb 2004
Posts: 702 |
Originally posted by BrApple: if the bearing is still making noise then there is a good chance that the bearing was pressed in wrong
iirc my father put a second ring in also on the last one since I had some extra hubs lying around, it didn't cause any unusual noises
I Had The Bearing Proffesionally Pressed, But I'm Sure a Mistake Could've Been Made.
CSVT E0 3L
14.5 @ 94mph, Stock Intake, Stock Exhaust minus Resonator, CEL, And Broken Pass. Side CV...Untuned.
|
|
|
|
Joined: Aug 2002
Posts: 30
New CEG\'er
|
OP
New CEG\'er
Joined: Aug 2002
Posts: 30 |
How do you know if the half shaft is good? I don't want to take of the rubber cover if I don't have to?
1998 Contour SE
MTX v6 loaded
1996 Mystique GS
ATX 4 cyl
|
|
|
|
Joined: Feb 2004
Posts: 702
Veteran CEG\'er
|
Veteran CEG\'er
Joined: Feb 2004
Posts: 702 |
Originally posted by bgailitis: How do you know if the half shaft is good? I don't want to take of the rubber cover if I don't have to?
Does It Pop Or Clunk Around Corners?? If Not Chances Are It's Good. Unless It Was Like Mine A Long Time Ago And Has Been Ground Down To A Fine Powdery/Grease Substance. Honestly It Should Be Fine. If You Squeeze The Boot Firmly You Should Be Able To Feel the CV Joint Inside. Give It Some Firm Pulls Up And Down And Side To Side (Not Out!). It Will Have A Small Amount Of Play In It. If This Is The Case AND you Are Not Getting Any Popping Or Clunking Noises When Turning Corners...Then No Worry's. You Could Always Just Buy A Quaife Or Torsen And Do The Burnout Test. Easiest Way I Know Of To Tell If My CV's Are Busted Or Not!!!
CSVT E0 3L
14.5 @ 94mph, Stock Intake, Stock Exhaust minus Resonator, CEL, And Broken Pass. Side CV...Untuned.
|
|
|
|
Joined: Aug 2002
Posts: 30
New CEG\'er
|
OP
New CEG\'er
Joined: Aug 2002
Posts: 30 |
The Axle is just hanging there - but it seems very loose and "stretched" scared it got damaged when removing the hub
1998 Contour SE
MTX v6 loaded
1996 Mystique GS
ATX 4 cyl
|
|
|
|
|
|