Register Log In

Contour Enthusiasts Group Archives Forums Modifications Duratec Performance HEADER INSTALL CHECK LIST :

Print Thread

Page 1 of 2

1

2

HEADER INSTALL CHECK LIST : #1533398 03/23/06 03:15 PM
Joined: Mar 2004 Posts: 288 Gwinnett , Ga 0 00SVTGA OP CEG\'er
OP 00SVTGA CEG\'er 0 Joined: Mar 2004 Posts: 288 Gwinnett , Ga	i'll be attempting to install my weapon-r hearders & y - pipe on my 2000 csvt this weekend. i've searched and found i'll need the following: - 13 mm deep well socket - 3/8 ratchet - u - joint for the 3/8 ratchet - socket extensions different sizes - 27 mm wrench or cresent wrench for the egr - 8 mm socket for the fan shroud removale - oil filter removale tool - oem exhaust mainifold gaskets - pb blast or wd-40 & lots of it will i be needing anything else ? will report with noticed power gains once installed. THANKS. the the day is finallly here !!! -2000 csvt silver frost #1619 -magnaflow 14415 -optimized T/B & y-pipe -superchips xgt1 -75mm proflow maf -K&N RU-3530 -fsvt smart pump # 354Z-9H307-BC -spec stage one, LSD -low-tek,a/f,oil press.,volts -B&M short shifter -17" konig gt-r

Re: HEADER INSTALL CHECK LIST : #1533399 03/23/06 03:23 PM
Joined: Apr 2002 Posts: 1,616 Not too close to you... M Mod-deth Hard-core CEG'er
Mod-deth Hard-core CEG'er M Joined: Apr 2002 Posts: 1,616 Not too close to you...	Originally posted by 00SVTGA: i'll be attempting to install my weapon-r hearders & y - pipe on my 2000 csvt this weekend. i've searched and found i'll need the following: - pb blast or wd-40 & lots of it will i be needing anything else ? will report with noticed power gains once installed. THANKS. the the day is finallly here !!! Don't even take the WD-40 off the shelf. No comparison to PB Blaster. If you can, spray all the nuts/bolts 24 hours before and let sit so it can work better.

Re: HEADER INSTALL CHECK LIST : #1533400 03/23/06 03:31 PM
Joined: Mar 2004 Posts: 288 Gwinnett , Ga 0 00SVTGA OP CEG\'er
OP 00SVTGA CEG\'er 0 Joined: Mar 2004 Posts: 288 Gwinnett , Ga	is pb plast sold at pepboys or autozone ? where can i find this ? -2000 csvt silver frost #1619 -magnaflow 14415 -optimized T/B & y-pipe -superchips xgt1 -75mm proflow maf -K&N RU-3530 -fsvt smart pump # 354Z-9H307-BC -spec stage one, LSD -low-tek,a/f,oil press.,volts -B&M short shifter -17" konig gt-r

Re: HEADER INSTALL CHECK LIST : #1533401 03/23/06 03:42 PM
Joined: Apr 2002 Posts: 1,616 Not too close to you... M Mod-deth Hard-core CEG'er
Mod-deth Hard-core CEG'er M Joined: Apr 2002 Posts: 1,616 Not too close to you...	For sure at AZ...not sure about Pepboys or AA...

Re: HEADER INSTALL CHECK LIST : #1533402 03/23/06 04:25 PM
Joined: Dec 2001 Posts: 6,910 Enfield, CT B BrApple_dup1 Hard-core CEG'er
BrApple_dup1 Hard-core CEG'er B Joined: Dec 2001 Posts: 6,910 Enfield, CT	Originally posted by 00SVTGA: is pb plast sold at pepboys or autozone ? where can i find this ? wal-mart in my area has it - 95 Mystique LS - Zetec/5spd - 99 Contour SeVT Sport - Duratec/5spd Official NE-CEG Contour/Mustang Family

Re: HEADER INSTALL CHECK LIST : #1533403 03/23/06 04:46 PM
Joined: May 2004 Posts: 3,637 Calgary, Alberta, Canada T Tourige Hard-core CEG\'er
Tourige Hard-core CEG\'er T Joined: May 2004 Posts: 3,637 Calgary, Alberta, Canada	liquid wrench rust remover is good too, spray it on the manifold bolts/studs, the y-pipe bolts, the catback bolts. Pretty much everything. Make sure you have ATLEAST 2 feet of extensions to get over the subframe. 99 TRed Contour SVT # 1853 out of 2760 230.2 WHP @ 6500 237.0 WTR @ 2250 Originally posted by MxRacer: Originally posted by RawBurt: I'll be keeping it to myself, until the time comes. It'll be hard to find. much like your weiner.

Re: HEADER INSTALL CHECK LIST : #1533404 03/23/06 05:04 PM
Joined: Mar 2004 Posts: 288 Gwinnett , Ga 0 00SVTGA OP CEG\'er
OP 00SVTGA CEG\'er 0 Joined: Mar 2004 Posts: 288 Gwinnett , Ga	do i have all the sockets and wrenches with the correct sizes? once i thought i saw that gear wrenches were needed. -2000 csvt silver frost #1619 -magnaflow 14415 -optimized T/B & y-pipe -superchips xgt1 -75mm proflow maf -K&N RU-3530 -fsvt smart pump # 354Z-9H307-BC -spec stage one, LSD -low-tek,a/f,oil press.,volts -B&M short shifter -17" konig gt-r

Re: HEADER INSTALL CHECK LIST : #1533405 03/23/06 05:18 PM
Joined: May 2004 Posts: 3,637 Calgary, Alberta, Canada T Tourige Hard-core CEG\'er
Tourige Hard-core CEG\'er T Joined: May 2004 Posts: 3,637 Calgary, Alberta, Canada	Originally posted by 00SVTGA: do i have all the sockets and wrenches with the correct sizes? once i thought i saw that gear wrenches were needed. bring 3/8 5/8 and 7/8, Also i think you need a 14mm deepsocket not a 13mm one, i cant remember tho. Also a 8mm socket for the Manifold studs. 99 TRed Contour SVT # 1853 out of 2760 230.2 WHP @ 6500 237.0 WTR @ 2250 Originally posted by MxRacer: Originally posted by RawBurt: I'll be keeping it to myself, until the time comes. It'll be hard to find. much like your weiner.

Re: HEADER INSTALL CHECK LIST : #1533406 03/23/06 05:22 PM
Joined: Mar 2003 Posts: 7,117 West Palm Beach, FL - Going to... T TourDeForce Hard-core CEG'er
TourDeForce Hard-core CEG'er T Joined: Mar 2003 Posts: 7,117 West Palm Beach, FL - Going to...	What size socket for dis-connecting the Y (assuming he'll replace it)? 15mm? Must be that jumbly-wumbly thing happening again.

Re: HEADER INSTALL CHECK LIST : #1533407 03/23/06 05:30 PM
Joined: May 2004 Posts: 3,637 Calgary, Alberta, Canada T Tourige Hard-core CEG\'er
Tourige Hard-core CEG\'er T Joined: May 2004 Posts: 3,637 Calgary, Alberta, Canada	Originally posted by TourDeForce: What size socket for dis-connecting the Y (assuming he'll replace it)? 15mm? 15mm or 14mm Bring both. 99 TRed Contour SVT # 1853 out of 2760 230.2 WHP @ 6500 237.0 WTR @ 2250 Originally posted by MxRacer: Originally posted by RawBurt: I'll be keeping it to myself, until the time comes. It'll be hard to find. much like your weiner.

Page 1 of 2

1

2

Moderated by GTO Pete

Link Copied to Clipboard

Powered by UBB.threads™ PHP Forum Software 7.7.5