Register Log In

Contour Enthusiasts Group Archives Forums General Group Buy Steeda Tri/Ax shifter

Print Thread

Page 1 of 2

1

2

Steeda Tri/Ax shifter #1011029 07/22/04 09:40 PM
Joined: Jul 2001 Posts: 2,728 Michigan R RyeLou OP Hard-core CEG\'er
OP RyeLou Hard-core CEG\'er R Joined: Jul 2001 Posts: 2,728 Michigan	Not really a group buy. Someone on e-bay is selling 9 more. It says its for the Focus, but it's the Focus with the MTX-75 so it will fit. After shipping, it's $94.99. US offer only. 7.75% tax in CA. http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&rd=1&item=7907686456&category=33736&sspagename=WD1V '03 SRT-4 50 trim turbo + support

Re: Steeda Tri/Ax shifter #1011030 07/23/04 12:22 PM
Joined: Jun 2002 Posts: 1,881 Philly burbs T TommySVT_dup1 Hard-core CEG'er
TommySVT_dup1 Hard-core CEG'er T Joined: Jun 2002 Posts: 1,881 Philly burbs	while that is a good deal, you still need to fab a riser plate for the 98-99's and if you own a 00, you need to fab a plate for under the car. Just wanted to let everyone know that before they jump on that good deal. 1998 T-Red SVT #957 Born 5/14/1997

Re: Steeda Tri/Ax shifter #1011031 07/23/04 06:15 PM
Joined: Jul 2001 Posts: 2,728 Michigan R RyeLou OP Hard-core CEG\'er
OP RyeLou Hard-core CEG\'er R Joined: Jul 2001 Posts: 2,728 Michigan	I was going to mention that. But you beat me to it. '03 SRT-4 50 trim turbo + support

Re: Steeda Tri/Ax shifter #1011032 07/23/04 08:24 PM
Joined: Jun 2004 Posts: 122 Raleigh, NC USA K Kinyoto CEG\'er
Kinyoto CEG\'er K Joined: Jun 2004 Posts: 122 Raleigh, NC USA	How hard would it be to fab a mounting plate...and how much$$ estimate?? www.kinyoto.com MYSPACE Music 98' Silver Contour SVT

Re: Steeda Tri/Ax shifter #1011033 07/23/04 09:01 PM
Joined: Jun 2002 Posts: 1,423 Eldersburg, MD S scottd60_dup1 Hard-core CEG\'er
scottd60_dup1 Hard-core CEG\'er S Joined: Jun 2002 Posts: 1,423 Eldersburg, MD	I can do the plates for both types (I did the last GB plates). Plates are $12 delivered. Scott Scott 2000 Contour SVT #1464 Mustang Dyno: 171.6hp/145.3lb Dynojet Dyno: 171.1hp/148.9lb 1989 20th Anniversary Turbo T/A "Indy 500 Pace Car" #1376 of 1550 All Original, 46k with a few mods 2002 F150 SuperCrew

Re: Steeda Tri/Ax shifter #1011034 07/24/04 12:41 AM
Joined: May 2003 Posts: 604 !>CALI<! S svt4b Veteran CEG\'er
svt4b Veteran CEG\'er S Joined: May 2003 Posts: 604 !>CALI<!	with the fab'd plate, how much better are they if any?? my B&M seems to be doing quite well. E0 silver #185 *3L hybrid+lots of mods DYNO(moderate tune): 205 whp/ 190ftlb http://www.cardomain.com/memberpage/449801

Re: Steeda Tri/Ax shifter #1011035 07/24/04 02:29 AM
Joined: May 2003 Posts: 5,600 Ocala, FL K KingpinSVT Addicted CEG\'er
KingpinSVT Addicted CEG\'er K Joined: May 2003 Posts: 5,600 Ocala, FL	i believe the shifts are the same length. since the steeda actually changes the pivot point, it can afford to be a little longer on the top, so you dont have to reach down quite as far as you do with the b&m. #4559 of 6535 born on Feb 17, 1998 Black 1998.5 CSVT FOR SALE [cleaning house]: SVT rear swaybar. Reasonable offer and its yours!

Re: Steeda Tri/Ax shifter #1011036 07/24/04 06:28 AM
Joined: Jul 2001 Posts: 2,728 Michigan R RyeLou OP Hard-core CEG\'er
OP RyeLou Hard-core CEG\'er R Joined: Jul 2001 Posts: 2,728 Michigan	Originally posted by scottd60: I can do the plates for both types (I did the last GB plates). Plates are $12 delivered. Scott Hey Scott. I wasn't sure if you wanted a part of this or not so I didn't mention anything. There are only 10 possible units, and I already bought one and spoke with you about the plate. Let me know when you're ready and I can send you the $12 '03 SRT-4 50 trim turbo + support

Re: Steeda Tri/Ax shifter #1011037 07/24/04 05:10 PM
Joined: Dec 2003 Posts: 161 AZ 9 95TourSleeper CEG\'er
95TourSleeper CEG\'er 9 Joined: Dec 2003 Posts: 161 AZ	so would they be compatible to the 95's and would it get rid of the reverse lock out? 98 Tour SVT #1819 custom turbo..again 95 Tour SE CTA intake,DND seats, removed cat/resonator,2.5" exhaust,98 SVT UIM and TB,9" K&N,custom turbo kit,greddy turbo timer,sunpro boost,oil psi,air/fuel gauges

Re: Steeda Tri/Ax shifter #1011038 07/24/04 08:18 PM
Joined: Jun 2002 Posts: 1,881 Philly burbs T TommySVT_dup1 Hard-core CEG'er
TommySVT_dup1 Hard-core CEG'er T Joined: Jun 2002 Posts: 1,881 Philly burbs	I don't think it'll work on the 95's. Yours is rod driven while 98+'s are cable driven. ( I might have that backwards). 1998 T-Red SVT #957 Born 5/14/1997

Page 1 of 2

1

2

Moderated by 1314_dup1

Link Copied to Clipboard

Powered by UBB.threads™ PHP Forum Software 7.7.5