warmonger............FORMER owner of a csvt???? - 07/10/06 01:50 AM
maybe i was just born yesterday, but what were you thinking warmonger? i feel betrayed!
why would you sell the CSVT!!!!
why would you sell the CSVT!!!!
Re: warmonger............FORMER owner of a csvt???? - 07/10/06 01:51 AM
PM's are cool.
Re: warmonger............FORMER owner of a csvt??? - 07/10/06 01:52 AM
He sold it because he chose to...
because he had built an incredible machine..
and because he was at a point in his life that he knew he had bigger and better plans!
That, and because I wanted to buy it!
because he had built an incredible machine..
and because he was at a point in his life that he knew he had bigger and better plans!
That, and because I wanted to buy it!
Re: warmonger............FORMER owner of a csvt??? - 07/10/06 01:54 AM
cool. anybody know what his bigger and better plans are???
oh and yeah i dont PM him because he doesnt check them much anymore it seems and this is easier, talking to you folks
oh and ray, i am supposed to ask how much its going to cost for a schematic of your turbo mani setup off that car!!!!
oh and yeah i dont PM him because he doesnt check them much anymore it seems and this is easier, talking to you folks
oh and ray, i am supposed to ask how much its going to cost for a schematic of your turbo mani setup off that car!!!!
Re: warmonger............FORMER owner of a csvt??? - 07/10/06 01:59 AM
Originally posted by TRicker:
cool. anybody know what his bigger and better plans are???
When it comes to Tom, you can NEVER TELL!!!!
He'll surprise anyone, I am sure, when he gets in to a project!
Re: warmonger............FORMER owner of a csvt??? - 07/10/06 02:07 AM
Ray, when did you get new dyno numbers? Are they official?
Re: warmonger............FORMER owner of a csvt??? - 07/10/06 02:18 AM
Originally posted by SVT4STD:
PM's are cool.
meh, over-rated
i am personally a big fan of the "shout out!" HOLLAAA!
Re: warmonger............FORMER owner of a csvt??? - 07/10/06 02:39 AM
That's a gray area. I had a minor problem on the car, and once out of the shop I dyno'd to make sure it was where I was when I put it IN the shop. I went ahead and popped off a 14psi run to see where I stood.
Since that run, I have been talking with Tom about trying to get the car's tune shifted a bit, as I am now running rich, (faulty MAF replaced, threw off the tables, slightly)
I don't have a scan of the dyno sheet to post, but could always get one. I can't, however, swear that it would pull that again (right now) with it running rich. I think after I get it dialed in a little tighter, I will dyno again, and see what I can top, then.
So, the numbers were "officially" done, but aren't officially posted, as I don't have the scan of the sheet available.
Since that run, I have been talking with Tom about trying to get the car's tune shifted a bit, as I am now running rich, (faulty MAF replaced, threw off the tables, slightly)
I don't have a scan of the dyno sheet to post, but could always get one. I can't, however, swear that it would pull that again (right now) with it running rich. I think after I get it dialed in a little tighter, I will dyno again, and see what I can top, then.
So, the numbers were "officially" done, but aren't officially posted, as I don't have the scan of the sheet available.
Re: warmonger............FORMER owner of a csvt??? - 07/10/06 05:18 AM
Originally posted by TRicker:
cool. anybody know what his bigger and better plans are???
oh and yeah i dont PM him because he doesnt check them much anymore it seems and this is easier, talking to you folks
oh and ray, i am supposed to ask how much its going to cost for a schematic of your turbo mani setup off that car!!!!
Dood... with warmonger being the great guy he is, he has many pictures and details freely available on his site.
Re: warmonger............FORMER owner of a csvt??? - 07/10/06 02:00 PM
if those numbers in your sig are it, than thats badass for stock internaled, homebuilt turbo car
Re: warmonger............FORMER owner of a csvt??? - 07/11/06 12:35 AM
Dood... with warmonger being the great guy he is, he has many pictures and details freely available on his site.
yep he has pics up. i asked him about it and he said that he didnt have any specs for the manifold he built, and that i should ask ray because he's a good guy and might help me out, when he needs to pull it off at least
yep he has pics up. i asked him about it and he said that he didnt have any specs for the manifold he built, and that i should ask ray because he's a good guy and might help me out, when he needs to pull it off at least