|
Joined: Sep 2000
Posts: 7,025
Hard-core CEG'er
|
Hard-core CEG'er
Joined: Sep 2000
Posts: 7,025 |
Im running a Lightning IAT. Youll have to solder it in the old the wiring, but it works.
Jim Hahn
1996 T-Red Contour SE Reborn 4/6/04
3.0L swap and Arizona Dyno Chip Turbo Kit
364 whp, 410 wtq @ 4,700 rpm
|
|
|
|
Joined: May 2003
Posts: 5,600
Addicted CEG\'er
|
Addicted CEG\'er
Joined: May 2003
Posts: 5,600 |
Originally posted by TC'd Swazo: Originally posted by MapOfTaziFoShoĆ¢ā??Ā¢: Should look like this i suppose.
Sweet, is it up and running??
That looks like a vortec to me? Even has the fuel pressure regulator. Stazi also has the aluminum UIM, no? Does look like his bay, but sans turbo.
#4559 of 6535 born on Feb 17, 1998
Black 1998.5 CSVT
FOR SALE [cleaning house]: SVT rear swaybar. Reasonable offer and its yours!
|
|
|
|
Joined: Nov 2000
Posts: 10,015
Hard-core CEG'er
|
OP
Hard-core CEG'er
Joined: Nov 2000
Posts: 10,015 |
That's offroad SVT not me. As if I'd go back to an inferior supercharger.
2000 SVT Turbo 295hp/269ftlb@12psi
#1 for Bendix Brakes Kits!
Knuckles rebuilt w/new bearings $55
AUSSIE ENDLINKS $70
Gutted pre-cats $80/set
A lack of planning on your part does not constitute an emergency on mine!
|
|
|
|
Joined: Aug 2001
Posts: 5,810
Hard-core CEG'er
|
Hard-core CEG'er
Joined: Aug 2001
Posts: 5,810 |
Originally posted by Stazi: Originally posted by WorldTour: Why do you want a lightning IAT? IAT are basically a dummy Ford Sensor and don't differ a great deal from vehicle to vehicle.
It's got to be the screw in type. Our IAT isn't made to seal into a pressurized area.
EDIT: I ordered the screw-in IAT from Part's America. It's going to cut it damn close!
I just used a die to thread my stock IAT(after I filed off the plastic ridge that held it into the stock intake), cut a piece of rubber for a gasket, then drilled and tapped a corresponding hole in the intercooler after the exchanger right before the TB for mounting. Screwed in tight and has held very solid with no leaks.
Took about 30 minutes, cost = $0.00
Spending no money and little effort to make a better part/product/mod.........Priceless.
Last edited by warmonger; 05/13/06 06:24 AM.
Former owner of '99 CSVT - Silver #222/2760
356/334 wHP/TQ at 10psi on pump gas!
See My Mods
'05 Volvo S40 Turbo 5 AWD with 6spd, Passion Red
'06 Mazda5 Touring, 5spd,MTX, Black
|
|
|
|
Joined: Feb 2003
Posts: 352
CEG\'er
|
CEG\'er
Joined: Feb 2003
Posts: 352 |
Good idea, War... Nice one!
FYI the ADC kit has the IAT in the pipe that goes into the turbo- I suppose it would serve the engine better to have it after the IC...
Dan G. and his Cougar
Forged internal (Diamond & Pauter) full 3L, "Monster" Kinger F/I cut & P&P, T3/4 60 trim .82A/R ADC turbo, SPEC Stage 3, Torsen, Greddy Profec-B SPEC II, Apex'i Timer, Lots of Gauges!
Used to have: 3.0L SVT hybrid
|
|
|
|
Joined: Sep 2000
Posts: 7,025
Hard-core CEG'er
|
Hard-core CEG'er
Joined: Sep 2000
Posts: 7,025 |
Originally posted by DanG: I suppose it would serve the engine better to have it after the IC...
Thats how mine is routed. Just tapped the Lightning IAT after the intercooler.
Jim Hahn
1996 T-Red Contour SE Reborn 4/6/04
3.0L swap and Arizona Dyno Chip Turbo Kit
364 whp, 410 wtq @ 4,700 rpm
|
|
|
|
Joined: Aug 2002
Posts: 4,970
Hard-core CEG'er
|
Hard-core CEG'er
Joined: Aug 2002
Posts: 4,970 |
That's where my IAT is, between the TB and IC.
2005 Ford F150 SuperCab FX4
1964 Chevrolet Impala SS
1998 CSVT: 354HP/328TQ @ 10 psi, now gone
|
|
|
|
Joined: Nov 2000
Posts: 10,015
Hard-core CEG'er
|
OP
Hard-core CEG'er
Joined: Nov 2000
Posts: 10,015 |
Got the IAT and it connects directly into the stock connector. I'm tapping and threading the intake manifold and putting it in there, just like the lightning setup. PS - motor is in, shopuld have it all done by tonight - tomorrow the latest.
2000 SVT Turbo 295hp/269ftlb@12psi
#1 for Bendix Brakes Kits!
Knuckles rebuilt w/new bearings $55
AUSSIE ENDLINKS $70
Gutted pre-cats $80/set
A lack of planning on your part does not constitute an emergency on mine!
|
|
|
|
Joined: Jul 2000
Posts: 3,119
Back In Black
|
Back In Black
Joined: Jul 2000
Posts: 3,119 |
How about those valve cover gaskets!
|
|
|
|
Joined: Nov 2000
Posts: 10,015
Hard-core CEG'er
|
OP
Hard-core CEG'er
Joined: Nov 2000
Posts: 10,015 |
You ARE THE MAN!
2000 SVT Turbo 295hp/269ftlb@12psi
#1 for Bendix Brakes Kits!
Knuckles rebuilt w/new bearings $55
AUSSIE ENDLINKS $70
Gutted pre-cats $80/set
A lack of planning on your part does not constitute an emergency on mine!
|
|
|
|
|