Contour Enthusiasts Group CEG

Modifications >> Forced Induction

Pages: 1 | 2 | 3 | 4 | (show all)
fst4dr
Hard-core CEG'er

Reged: 05/27/00
Posts: 1020
Loc: North Carolina
Forced Induction Info Thread
#349778 - 07/16/03 01:27 AM

Please read through this thread before asking any questions that you think might have bee asked already. You may find what you need and wont have to post.

Please keep the idle citchat to a minimum, just good information in this thread.

It may take a little while to get lots of information in here, but its a good idea anyways.

Lets see some good stuff

--------------------
Simon
new- '04 Dodge Dakota 4x4. V8, 5spd FOR SALE
Black 98 SVT EO (#2119 of 6535)- SOLD!
New project-'88 Ranger 302 swap.



Post Extras: Print Post Remind Me! Notify Moderator
onosway
Hard-core CEG'er

Reged: 04/12/01
Posts: 2230
Re: Forced Induction Info Thread new
#349987 (Re: fst4dr) 07/16/03 04:17 AM

Standard Street Flight Kit includes (parts can be upgraded):

Garrett T-28
Dual ball bearing liquid cooled

Headers
321 Stainless headers, 304L downpipe and intake pipes
Downpipe includes flex and 3" high flow cat

Filter
7" K&N

Intercooler
Liquid to air

Blow Off Valve
Turbo XS types S

Wastegate
Tial 35mm divorced wastegate by Garrett

Heat Exchanger
8 pass 1/2"

Reservoir Tank
4 gallon aluminum reservoir tank, with aviation style lid

Intercooler pump
198 gph

Injectors
6 24# Ford

Spark plugs
6 NGK

Engine Management
Custom dyno tuned Street Flight chip

Ventilation
Catch can with breather

Battery hold down kit
0 gauge battery line, eyelets and hold downs

Misc.
All silicone for intake, all bolts, oil lines and fittings, brass, vacuum tees and plenty of hose clamps.

Total cost is $5000.

--------------------
MY NEW HOBBY...RUINING CHRIS CROFTS LIFE...

Post Extras: Print Post Remind Me! Notify Moderator
onosway
Hard-core CEG'er

Reged: 04/12/01
Posts: 2230
Re: Forced Induction Info Thread new
#349991 (Re: onosway) 07/16/03 04:18 AM

wavrdr's STREET FLIGHT: 13 second run - 2.5L - 5psi Florida
StreetFlight Kit (prototype?)
300 wHP, 261 TQ - warmongers turbo
Warmongers 3L Turbo Project
Kingers 3L Supercharged Cougar
Twin Turbo Duratec (stop stroking)

--------------------
MY NEW HOBBY...RUINING CHRIS CROFTS LIFE...

Post Extras: Print Post Remind Me! Notify Moderator
VenomSVT
CEG'er

Reged: 08/22/02
Posts: 74
Loc: KC, KS
Re: Forced Induction Info Thread new
#350557 (Re: fst4dr) 07/16/03 06:02 PM

Nitrous-

Nitrous is not like the movies. You cant just slap on a 200 shot and expect your motor to live long. First thing you need to do if you are considering nitrous is learn as much as you can. There are many places on the internet that can help and books that explain how it works. Another thing.it NITROUS, not NOS. N.O.S is a company that makes nitrous kits and it stands for Nitrous Oxide Systems. Here are a couple things to know.

-What size shot can your car handle?: As a general rule, you can spray 50% of what your base engine horse power is. So for an SVT which is rated at 200 hp, the largest you would want is 100 shot.

-What is needed for nitrous?

Needed items: Nitrous Kit, colder plugs with a smaller gap, and common sense when using it.

Recommended items: Purge kit, window switch, bottle heater, A/F gauge, nitrous gauge, fuel pressure gauge, and chip.

-Plugs: A general rule for plugs is one step colder for every 50-75 hp. Start off with one step colder and monitor the plugs for flecks of aluminum, a sure sign of detonation. Do not ever run platinum or splitfire type plugs, copper is what you want. Gap the plugs smaller than normal plugs. Nitrous companies recommend .035 but the odds of snuffing out your spark are very small. Most people run a .040-.045 to get a better burn.

-Timing: As another general rule it is recommend that you retard the timing 1-2* for every additional 50 hp you add. By using a higher octane fuel you can get away with less timing and still be safe. But reducing the timing will lessen the chance of detonation and pinging.

-Octane: When using nitrous in any quantity it is best to use a higher octane fuel. Higher octane fuels reduce the chance of detonation. Avoid detonation and pinging like the plague. It will spell certain disaster for a nitrous injected motor. A bottle of octane booster is not a bad idea either, but should not take the place of higher octane fuel.

-Wet, Dry, or Direct Port: Wet kits use one nozzle to supply both the nitrous and fuel into the intake. Dry kits spray the nitrous into the intake and use the existing injectors to supply the extra fuel. Direct port systems supply the nitrous and fuel to each individual intake runner on the motor, or one per cylinder.



I will go over the Venom Kits.

The Venom kits will work with any year Contour V6. They work with both returnless and return style fuel systems. Both kits are computer controlled and tap into your injectors, O2 sensor, and TPS. With the computer control you get A/F monitoring, which means if you start to run lean the nitrous will automatically be shut off. They also use the existing injectors to compensate for the fuel that is needed due to the extra air (nitrous). These kits are in my opinion the safest you can buy.

VCN-1000 - This is the basic nitrous kit with all the safety precautions just not all the frills. The VCN-1000 comes with the computer control box, bottle, lines, wiring harness and 4 nitrous nozzles to select the shot size (25, 50, 75, 100).

VCN-2000 - This is the kit with it all. The VCN-2000 kit comes with computer control box, bottle, lines, wiring harness, digital display module, and a variable valve. With this system you need a computer to download to the control box the points at which you can set throttle angle, RPM activation, and percentage of nitrous. There are 3 different modes to choose from Linear, Drag, and Timed. Linear mode starts with a small shot and works its way up to the full selected output. In the drag setting the full selected shot is sprayed when the activation RPM is reached. And finally timed is for the turbo people. It will spray for 3-4 seconds, by that time the turbo is spooled up and can take over. The digital display lets you keep an eye on what is going on. It features RPM, nitrous status, mode, exhaust (rich or lean), and injector pulse width.


--------------------
2002 Mustang GT
H&R, Bilstein, NX, K&N, Bassani, and Prochamber
03 Cobra wheels, Goodyear Eagles: 275 fronts, 315 rears
325HP and 433 ft-lbs at the wheels

Old Car:
2000 SVT #463/2150
Best #'s - 268.5HP and 275.8 ft-lbs at the wheels

Post Extras: Print Post Remind Me! Notify Moderator
Rev. Po-Jay
Veteran CEG'er

Reged: 07/31/01
Posts: 829
Loc: !Surprise Arizona!
Re: Forced Induction Info Thread new
#350950 (Re: VenomSVT) 07/16/03 11:58 PM

Refer to the following information page and forever be changed!
How Stuff Works / Supercharger and Turbo

This site is very informative and can answer anything from Forced Induction to "How does a rotary engine work?".... Have fun. Knowledge is power.


Dyno Plot of N/A vs. Vortech on 98E0


Timeslip with 2.5L Vortech'd Contour

Thanks Simon!

--------------------
SVT Parts For Sale!PM Me.
2006 M6 Cyclone Gray GTO
1995 Mazda Protege Commuter Special
93 FXDWG Dyna Wide Glide

I'm A TROLL Now!~

Edited by Rara (07/17/03 10:24 PM)

Post Extras: Print Post Remind Me! Notify Moderator
RaraAdministrator
"Absolut Rara."

Reged: 09/09/00
Posts: 3223
Loc: Westland, MI
Re: Forced Induction Info Thread *DELETED* new
#350959 (Re: Rev. Po-Jay) 07/17/03 12:05 AM

Post deleted by Rara

--------------------
Balance is the Key.

rarasvt@comcast.net

Post Extras: Print Post Remind Me! Notify Moderator
onosway
Hard-core CEG'er

Reged: 04/12/01
Posts: 2230
Re: Forced Induction Info Thread new
#351088 (Re: Rara) 07/17/03 02:00 AM

FYI: Duratec related
Twin Turbo a Contour?
Another twin turbo post
Intercooler talk w/twin turbo talk


--------------------
MY NEW HOBBY...RUINING CHRIS CROFTS LIFE...

Post Extras: Print Post Remind Me! Notify Moderator
onosway
Hard-core CEG'er

Reged: 04/12/01
Posts: 2230
Re: Forced Induction Info Thread new
#351223 (Re: onosway) 07/17/03 03:52 AM

Front mounted I/C

For a guy that doesn't have a turbo (yet), I am posting here quite a bit

--------------------
MY NEW HOBBY...RUINING CHRIS CROFTS LIFE...

Post Extras: Print Post Remind Me! Notify Moderator
LegacySHO
CEG'er

Reged: 07/31/01
Posts: 130
Loc: Toronto, Ontario
Re: Forced Induction Info Thread new
#398417 (Re: onosway) 09/07/03 10:44 PM

Here's some more info I think would be great in this thread:

- Info on what kind of knowledge would be required for installation of the turbo kit (i.e. could any mechanic do it? Are there instructions included? Does the installation need to be done at Street Flight?)
- A sort of history on the Vortech kit, i.e. I know there was initially a problem with spline stripping on the jack shaft, has that been verified to be fixed on the kits currently shipping? Are there any other problems that potential buyers should be aware of?
- Contact info for Street Flight (name/phone #, etc.)

I know I'm sticking my neck out to get flamed here but I was thinking that this info might be included here to save time for others looking for the same information.

--------------------
1998.5 SVT Contour - Black
H&R's
Optimized Y-pipe and TB
Open element intake w/heat shield
18x8 Mas Italy Axels (40 offset) w/225/40/18
2x Kicker 8" midbass "subs" in rear deck (infinite baffle setup)
A few more little things...(like bushings)

Post Extras: Print Post Remind Me! Notify Moderator
18psi2300
Hard-core CEG'er

Reged: 03/23/01
Posts: 2091
Loc: Dublin, Oh
Re: Forced Induction Info Thread new
#411768 (Re: LegacySHO) 09/23/03 04:55 AM

Great page on turbo theory...
http://www.turbodriven.com/en/turbofacts/index.asp

How to read a compressor map...
http://www.stealth316.com/2-3s-compflowmaps.htm



--------------------
Nick Johnson
87' & 88' Thunderbird TC
96' Contour SE Midnight Red ATX


Post Extras: Print Post Remind Me! Notify Moderator
Bradness
CEG'er

Reged: 06/01/00
Posts: 291
Loc: Greater Toronto Area, Canada
Re: Forced Induction Info Thread new
#480921 (Re: 18psi2300) 12/16/03 07:07 PM

Don't know about other states/provinces/countries but Nitrous is very illegal here. Too many street racers killed in a ball-of-flames when the Nitrous ruptured and fanned the flames.

Personally, I rather be blown!

--------------------
Redcoat Raceworks. Performance parts and custom fabricating for Contours, Mystiques and Cougars. Specializing in chassis and suspension parts. Custom end links, control arms, strut tower bars, engine torque braces, etc.

Post Extras: Print Post Remind Me! Notify Moderator
akrump47
Hard-core CEG'er

Reged: 12/23/02
Posts: 1475
Loc: Novi or Dearborn MI
Re: Forced Induction Info Thread new
#481004 (Re: Bradness) 12/16/03 08:32 PM

Originally posted by Bradness:

Personally, I rather be blown!




Uhhhh . . .

--------------------
E0 3781

Post Extras: Print Post Remind Me! Notify Moderator
NICEGUY
Newbie

Reged: 04/06/04
Posts: 2
Loc: Mississauga/Ontario/Canada
Re: Forced Induction Info Thread new
#580172 (Re: Bradness) 04/06/04 01:32 AM

Originally posted by Bradness:
Don't know about other states/provinces/countries but Nitrous is very illegal here. Too many street racers killed in a ball-of-flames when the Nitrous ruptured and fanned the flames.

Personally, I rather be blown!




Nitrous is not illegal in Ontario Canada. The MTO states you can carry a certain amount of nitrous as long as it is mounted securely and safely stored in your vehicle within their guidelines.
You can not have a remote bottle opener or the bottle on. I'm sure if you were to go by a local ministry transportation building one of the officers would be willing to teach you about the laws.

Post Extras: Print Post Remind Me! Notify Moderator
auiotour
Hard-core CEG'er

Reged: 09/17/02
Posts: 4294
Loc: Auburn, WA (15min S of Seattle)
Re: Forced Induction Info Thread new
#782543 (Re: NICEGUY) 12/02/04 05:09 PM

Just thought this should have been added. I know if I would have found this thread a month ago I would have got the chance to save my super charger. This is for those who have Rev 1 or Rev 2 of the Vortech Super Charger. I recommend installing this kit ASAP. I didn't as we didn't disconnect the jackshaft from the super charger the car was prevouisly installed on and drove for several thousands of mile swith no problem. Figure we could do the same we installed it without disconnecting it. unfornently it was splined correctly inside and within 75 short miles both the male and female ends of the jackshaft were destroyed. Striped of all their splines. And All i have to say is this should have been a sticky long ago.

http://www.contour.org/ubbthreads/showflat.php?Cat=&Board=turbo&Number=256308&page=&view=&sb=5&o=&fpart=1&vc=1

Another alternative I was just informed of is the Lovejoy connectors. Don't know to much about them. But it could save you time and money. Something I wish I had both of after not seeing these before hand. Again these are a must see for vortech systems.

http://www.directindustry.com/soc/lovejoy/backlash-free-couplings-7199-59843.html?&RefCat=L

--------------------
95 SES Sold
99 SE Sport Sold
99 SVT T-Red Tan Interior. K&N, Magnecors, 19' Theorys, And some audio stuff.

Post Extras: Print Post Remind Me! Notify Moderator
Loco4G63
CEG road warrior

Reged: 08/01/01
Posts: 17248
Loc: IL
Re: Forced Induction Info Thread new
#782921 (Re: fst4dr) 12/02/04 11:59 PM

Jackson Racing supercharger for Focus Zetec on Contour- Here is a brief list of what had to be done:

Install went according to the instructions but a few things had to "made"

-A plate to block off the EGR (for us 98+ Contours)
-Part of a bracket that the new intake manifold is supported on will need to fabbed
-You will need to get a IAC valve from a Focus.....the Contour IAC connector goes out in a 90 degree angle (which will hit the intake manifold)...the Focus connector goes out straight
- to get the alternator bolts in you will have to raise the engine
-if you have a UDP you will need to find your stock one.....Underdriving the S/C will give lower boost
-you will basically have to eliminate the cruise control....the way TB bolts up to the S/C the bracket sits kind of high....so a Dremel is you friend-----cut the piece of braket where the C/C goes....didn't matter to me....I never use it.
-CTA would probably be a better option for a "bolt on" intake....all I had to do is cut it and reverse it.

Other than that we just followed the instructions.

--------------------
Hector

2003 Rally Red Mitsubishi Evolution VIII
257HP/259TQ


2005 Lapis Blue Mazda 6s

RET: 00 Cabernet Red Ford Contour Zetec ATX SUPERCHARGED
160HP/141TQ





Post Extras: Print Post Remind Me! Notify Moderator
wanabsvt
New CEG'er

Reged: 07/25/03
Posts: 14
Loc: Edmonton,Alberta,Canada.
Re: Forced Induction Info Thread new
#800638 (Re: onosway) 12/22/04 10:32 PM

where can I buy the kit?

Post Extras: Print Post Remind Me! Notify Moderator
beyondloadedSE
Hard-core CEG'er

Reged: 09/29/00
Posts: 7025
Loc: Fort Wayne, IN
Re: Forced Induction Info Thread new
#800642 (Re: wanabsvt) 12/22/04 10:42 PM

Originally posted by wanabsvt:
where can I buy the kit?




www.arizonadynochip.com

--------------------
Jim Hahn
1996 T-Red Contour SE Reborn 4/6/04
3.0L swap and Arizona Dyno Chip Turbo Kit
364 whp, 410 wtq @ 4,700 rpm


Post Extras: Print Post Remind Me! Notify Moderator
wanabsvt
New CEG'er

Reged: 07/25/03
Posts: 14
Loc: Edmonton,Alberta,Canada.
Re: Forced Induction Info Thread new
#805283 (Re: beyondloadedSE) 12/29/04 07:55 PM

Thanks for your response.I checked it out.unfortunately,they don't make a kit for atx.

Post Extras: Print Post Remind Me! Notify Moderator
CSVT985
Veteran CEG'er

Reged: 11/22/04
Posts: 759
Loc: Roanoke, Texas
Re: Forced Induction Info Thread new
#811528 (Re: wanabsvt) 01/06/05 09:22 PM


I FOUND A TURBO KIT FOR UNDER $200!!1!

OMG LOLOZORS!!1! 1M GOING TO GO RACE AND BEAT EVERYONE EVEN THEm TRANSAMS!!1!

I mean, how awesome is that!! I spend nothing and get what others pay $5000 for. It almost looks unsafe...BUT THIS IS EBAY!!!11 How COOLZZORS!!

http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&rd=1&item=7945507474&category=33742

--------------------
E0 #4384 of 6535
Born Jan. 9 1998
My SVT from the ashes
147,466 miles, purchased Nov. 2002 @ 76,559 miles

Post Extras: Print Post Remind Me! Notify Moderator
CSVT985
Veteran CEG'er

Reged: 11/22/04
Posts: 759
Loc: Roanoke, Texas
Re: Forced Induction Info Thread new
#811536 (Re: CSVT985) 01/06/05 09:26 PM

On another note. Do those heat shields really make a difference.

If so where do you purchase them?

I wish I had turbo...but maybe on my next CSVT - my old girl would probably blow her pistons right out.

--------------------
E0 #4384 of 6535
Born Jan. 9 1998
My SVT from the ashes
147,466 miles, purchased Nov. 2002 @ 76,559 miles

Post Extras: Print Post Remind Me! Notify Moderator
beyondloadedSE
Hard-core CEG'er

Reged: 09/29/00
Posts: 7025
Loc: Fort Wayne, IN
Re: Forced Induction Info Thread new
#812480 (Re: CSVT985) 01/07/05 10:31 PM

I hope your joking about that paperweight you listed from ebay.

most people just make their own heatshield and yes, they do make quite a big difference in stand still traffic.

--------------------
Jim Hahn
1996 T-Red Contour SE Reborn 4/6/04
3.0L swap and Arizona Dyno Chip Turbo Kit
364 whp, 410 wtq @ 4,700 rpm


Post Extras: Print Post Remind Me! Notify Moderator
CSVT985
Veteran CEG'er

Reged: 11/22/04
Posts: 759
Loc: Roanoke, Texas
Re: Forced Induction Info Thread new
#812611 (Re: beyondloadedSE) 01/08/05 01:54 AM

Yes I was making a joke hence the hacker/noob/ricer talk

I laugh at ppl buying them.

Thanks about the heatshield too, I will search the forums to see if someone has listed a How-To

--------------------
E0 #4384 of 6535
Born Jan. 9 1998
My SVT from the ashes
147,466 miles, purchased Nov. 2002 @ 76,559 miles

Post Extras: Print Post Remind Me! Notify Moderator
99svtContourMan
New CEG'er

Reged: 02/25/05
Posts: 36
Loc: Las Vegas
Re: Forced Induction Info Thread new
#860375 (Re: CSVT985) 02/27/05 01:23 AM

I am going to put a turbo kit on from Az dyno I was just wondering what all of you thought would be good upgrades for the engine. diamond pistons etc... to make the engine last awhile. What all would you do if money was not an issue.

Post Extras: Print Post Remind Me! Notify Moderator
Keyser Soze
Hard-core CEG'er

Reged: 03/26/01
Posts: 1860
Loc: The Sonoran Desert
Re: Forced Induction Info Thread new
#860383 (Re: 99svtContourMan) 02/27/05 01:28 AM

Depends on how fast you want to go.

--------------------
2001 Lincoln LS8
1994 Lexus GS300

Post Extras: Print Post Remind Me! Notify Moderator
svtProdigy
Hard-core CEG'er

Reged: 12/13/04
Posts: 1190
Loc: Carol Steam, IL
Re: Forced Induction Info Thread new
#860395 (Re: 99svtContourMan) 02/27/05 01:41 AM

"What all would you do if money was not an issue". Is this not the case? If money is no issue than i don't know what pistons to go with. I got diamond pistons. Those should work fine. I would bore it sleeve it, I would Buy titanium rods and shave the crank. balance the engine . THis could quite literally keep going and going and going...........no i simply undersand what you mean. IF you want 400whp its recommended to get forged rods and pistons. If you are going to be under that get custom pistons, main bearings and stronger rod bolts. someone else can fill in or recommend something else i missed.


--------------------
PLEASE HELP ME GET MY CAR TOGETHER! ITS IN DAYTON OHIO! I need the motor together and in the car so i can DRIVE it! Pleeeeeese!
diamond pistons for 3.0/forsale
#702 of 2150

Edited by svtProdigy (02/27/05 01:42 AM)

Post Extras: Print Post Remind Me! Notify Moderator
99svtContourMan
New CEG'er

Reged: 02/25/05
Posts: 36
Loc: Las Vegas
Re: Forced Induction Info Thread new
#860437 (Re: svtProdigy) 02/27/05 02:43 AM

OK lets say you did want over 400whp what would you do to the engine to make it handle the horse power.


Post Extras: Print Post Remind Me! Notify Moderator
Keyser Soze
Hard-core CEG'er

Reged: 03/26/01
Posts: 1860
Loc: The Sonoran Desert
Re: Forced Induction Info Thread new
#860439 (Re: 99svtContourMan) 02/27/05 02:45 AM

Buy Suneils car. It already does 400 wheels and will save you months of hassle.

--------------------
2001 Lincoln LS8
1994 Lexus GS300

Post Extras: Print Post Remind Me! Notify Moderator
99svtContourMan
New CEG'er

Reged: 02/25/05
Posts: 36
Loc: Las Vegas
Re: Forced Induction Info Thread new
#860441 (Re: Keyser Soze) 02/27/05 02:49 AM

Yes I saw that car on e-bay but it didn't meet the reserve. That car is awsome and the buy now price was only 18k. The only problem is I already have a 99csvt with only 26k miles on it.

Edited by 99svtContourMan (02/27/05 02:52 AM)

Post Extras: Print Post Remind Me! Notify Moderator
Keyser Soze
Hard-core CEG'er

Reged: 03/26/01
Posts: 1860
Loc: The Sonoran Desert
Re: Forced Induction Info Thread new
#860454 (Re: 99svtContourMan) 02/27/05 03:03 AM

I already did it once and sold it to The Ford Guy on these forums. Here is a quick break down.

Engine:
99 SVT block - 300

9:1 Diamond Racing pistons - 700
Chrome steel Total Seal rings
Custom wrist pins
Pauter rods - 1030
Clevite 77 rod bearings -100
Federal Mogul main bearings
Street Flight turbo kit - 5000
T3/4 upgrade - 550
Custom P&P heads 3L valves – 1400
Custom 3” exhaust – 400
Turbo XS boost controller - 70
Focus SVT fuel pump - 85

Transmission:

Torsen – 650
SPEC III – 399
Shifter – 30
Stage II axles – 700

Wheels/tires/suspension/other:

Kumho Mx – 600
Ground Control – 450
Koni struts – 540
Street Flight RSB – 90
Sub frame connectors - 150
Battery kill switch - 40

That's $13284 plus labor and other misc stuff you will need. Sell your car and buy Suneil's.






--------------------
2001 Lincoln LS8
1994 Lexus GS300

Post Extras: Print Post Remind Me! Notify Moderator
Horse
Hard-core CEG'er

Reged: 06/12/01
Posts: 4777
Loc: Cobra Heaven
Re: Forced Induction Info Thread new
#860461 (Re: svtProdigy) 02/27/05 03:08 AM

Originally posted by svtProdigy:
stronger rod bolts.





im seriously off tpic - but damn boy -

--------------------
Tea 82 242Ti
Proud former owner - Samantha
'98 SVT #2253

Reborn Aug 21 2002
Cobra Paradise

Post Extras: Print Post Remind Me! Notify Moderator
99svtContourMan
New CEG'er

Reged: 02/25/05
Posts: 36
Loc: Las Vegas
Re: Forced Induction Info Thread new
#860482 (Re: Horse) 02/27/05 04:01 AM

Is that all it would cost. Ok then I'm going to do it. I have talked with Az dyno and he could pretty much do it all. I think I will get better valve springs and baer brakes. Is there any other good mods I could do that you haven't listed

Post Extras: Print Post Remind Me! Notify Moderator
stocksvtcontour
CEG'er

Reged: 11/15/05
Posts: 217
Loc: warren mi
Re: Forced Induction Info Thread new
#1103580 (Re: auiotour) 11/17/05 08:44 PM

This is to the guy who mentioned the lovejoy connectors. they are for connecting electric motors to drives. they can take some misalinment depending on the insert. I run a power transmission warehouse and i know these types of products well. And by power transmission it does not mean automobile transmissions. any questions email me @ armyboy6310@gmail.com
joe

--------------------
2000 svt contour
1996 oldsmobile eighty-eight


Post Extras: Print Post Remind Me! Notify Moderator
Stazi
Hard-core CEG'er

Reged: 11/18/00
Posts: 10015
Loc: The land of Vegemite and Foster's (Actually Livonia, MI)
Re: Forced Induction Info Thread new
#1103582 (Re: stocksvtcontour) 11/17/05 08:46 PM

I know about lovejoy connections - I use to use them on industrial (mining)equipment. The intended use in this application is ONLY to drive a supercharger - NOT the transmission!

--------------------
2000 SVT Turbo 295hp/269ftlb@12psi
#1 for Bendix Brakes Kits!
Knuckles rebuilt w/new bearings $55
AUSSIE ENDLINKS $70
Gutted pre-cats $80/set

A lack of planning on your part does not constitute an emergency on mine!

Post Extras: Print Post Remind Me! Notify Moderator
Cerevo
Newbie

Reged: 06/26/06
Posts: 7
Re: Forced Induction Info Thread new
#1270872 (Re: Stazi) 07/02/06 05:36 AM

so are there any supercharger kits under $3k for the svt?
btw im new and am coming from an escort POV

--------------------
my zx2 is slow...

Post Extras: Print Post Remind Me! Notify Moderator
MapOfTaziFoSho
Hard-core CEG'er

Reged: 09/01/02
Posts: 9065
Loc: The E.L.
Re: Forced Induction Info Thread new
#1270956 (Re: Cerevo) 07/02/06 04:28 PM

Originally posted by Cerevo:
so are there any supercharger kits under $3k for the svt?
btw im new and am coming from an escort POV




Ever heard of searching?!

--------------------
Born again on 04/09/06
FOR SALE:
Moonroof glass and motor MB sunshade
PM ME!


Post Extras: Print Post Remind Me! Notify Moderator
Keyser Soze
Hard-core CEG'er

Reged: 03/26/01
Posts: 1860
Loc: The Sonoran Desert
Re: Forced Induction Info Thread new
#1270962 (Re: MapOfTaziFoSho) 07/02/06 04:58 PM

If you want to smash a newb, you can at least point him in the right direction. Use the search criteria below.

Thomas Knight supercharger

--------------------
2001 Lincoln LS8
1994 Lexus GS300

Post Extras: Print Post Remind Me! Notify Moderator
Pages: 1 | 2 | 3 | 4 | (show all)


Extra information
0 registered and 16 anonymous users are browsing this forum.

Moderator:   

Print Thread

Permissions
You cannot start new topics
You cannot reply to topics
HTML is disabled
UBBCode is enabled

Thread views: 18271

Jump to

Contact Us Contour.org

*
UBB.threads™ 6.2.3

Generated in 0.018 seconds in which 0.01 seconds were spent on a total of 14 queries. Zlib compression enabled.

Copyright 1999-2005 Lance Kinley

CEG and contour.org are not affiliated with nor endorsed by Ford Motor Company