Contour Enthusiasts Group CEG

Modifications >> Transaxle

Pages: 1 | 2 | >> (show all)
Pole120
Hard-core CEG'er

Reged: 03/16/04
Posts: 4141
Loc: New Berlin, WI
Re: My SVT doesn't have a stab o shock new
#1228720 (Re: fastcougar) 05/01/06 12:48 AM

Originally posted by fastcougar:
It's crap ... poly fill the roll resistor instead. I have seen some 85A shore hardness epoxy filler if 94A is too stiff for your liking.




85 isn't much softer....i did a set of forward LCA's in 85 and it still seemed prety stiff.

--------------------
99 SE V6\5spd - 156 HP\157 TQ 15.166-90.84
Totaled 02/12/06

99 SVT # 1571 - 175 HP\153 TQ 14.999-91.88
Born 3/24/99 Reborn 3/18/06
Pietenpol Racing Technologies project vehicle

90 Festiva L 5spd, Blue(not for long), 103k

Post Extras: Print Post Remind Me! Notify Moderator
Russell-3L
Hard-core CEG'er

Reged: 08/23/02
Posts: 3732
Loc: Pittsburgh, PA
Re: My SVT doesn't have a stab o shock new
#1228734 (Re: Pole120) 05/01/06 01:11 AM

Originally posted by pole120:
Originally posted by fastcougar:
It's crap ... poly fill the roll resistor instead. I have seen some 85A shore hardness epoxy filler if 94A is too stiff for your liking.




85 isn't much softer....i did a set of forward LCA's in 85 and it still seemed prety stiff.




how did the urethane control arms turn out?

ive been contemplating taht for a while now...

--------------------
Russell
Oval Port 3L Nearly Done
MTX75 w/ Homebrew Zetec FD and Torsen Complete

Post Extras: Print Post Remind Me! Notify Moderator
Pole120
Hard-core CEG'er

Reged: 03/16/04
Posts: 4141
Loc: New Berlin, WI
Re: My SVT doesn't have a stab o shock new
#1228811 (Re: Russell-3L) 05/01/06 03:05 AM

Originally posted by Russell-3L:
Originally posted by pole120:
Originally posted by fastcougar:
It's crap ... poly fill the roll resistor instead. I have seen some 85A shore hardness epoxy filler if 94A is too stiff for your liking.




85 isn't much softer....i did a set of forward LCA's in 85 and it still seemed prety stiff.




how did the urethane control arms turn out?

ive been contemplating taht for a while now...




Don't know....Stazi has them...i'm not sure if they've ever been installed.....i was going to offer the service if they proved to last and perform. The time and cost involved to produce them would be outrageous and i'm no longer persuing the idea. I would however like to know how they perform....

--------------------
99 SE V6\5spd - 156 HP\157 TQ 15.166-90.84
Totaled 02/12/06

99 SVT # 1571 - 175 HP\153 TQ 14.999-91.88
Born 3/24/99 Reborn 3/18/06
Pietenpol Racing Technologies project vehicle

90 Festiva L 5spd, Blue(not for long), 103k

Post Extras: Print Post Remind Me! Notify Moderator
MapOfTaziFoSho
Hard-core CEG'er

Reged: 09/01/02
Posts: 9065
Loc: The E.L.
Re: My SVT doesn't have a stab o shock new
#1228839 (Re: Pole120) 05/01/06 04:08 AM

Originally posted by pole120:
Originally posted by Russell-3L:
Originally posted by pole120:
Originally posted by fastcougar:
It's crap ... poly fill the roll resistor instead. I have seen some 85A shore hardness epoxy filler if 94A is too stiff for your liking.




85 isn't much softer....i did a set of forward LCA's in 85 and it still seemed prety stiff.




how did the urethane control arms turn out?

ive been contemplating taht for a while now...




Don't know....Stazi has them...i'm not sure if they've ever been installed.....i was going to offer the service if they proved to last and perform. The time and cost involved to produce them would be outrageous and i'm no longer persuing the idea. I would however like to know how they perform....




I've seen em, I'll get him to install them on hist car when he pulls the motor out!

--------------------
Born again on 04/09/06
FOR SALE:
Moonroof glass and motor MB sunshade
PM ME!


Post Extras: Print Post Remind Me! Notify Moderator
Pages: 1 | 2 | >> (show all)


Extra information
0 registered and 10 anonymous users are browsing this forum.

Moderator:  RoadRunner, unisys12 

Print Thread

Permissions
You cannot start new topics
You cannot reply to topics
HTML is enabled
UBBCode is enabled

Thread views: 917

Jump to

Contact Us Contour.org

*
UBB.threads™ 6.2.3

Generated in 0.022 seconds in which 0.016 seconds were spent on a total of 14 queries. Zlib compression enabled.

Copyright 1999-2005 Lance Kinley

CEG and contour.org are not affiliated with nor endorsed by Ford Motor Company