Contour Enthusiasts Group CEG

General >> Group Buy

Pages: 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 | 17 | 18 | (show all)
KnuKonceptz
Hard-core CEG'er

Reged: 03/30/01
Posts: 1279
Loc: Cleveland,OH
Re: P.R.T. Poly Roll Resistors new
#1120367 (Re: Pole120) 12/08/05 05:31 PM

bummer, I'll see if I have another rear mount to use as a core.

--------------------
Previous Owner of 00 SVT Contour #1077/2150
95 Contour SE '01 3L


Post Extras: Print Post Remind Me! Notify Moderator
darpinian
CEG'er

Reged: 10/09/03
Posts: 301
Loc: San Antonio Tx
Re: P.R.T. Poly Roll Resistors new
#1128282 (Re: KnuKonceptz) 12/18/05 11:59 AM

I have a couple of questions..

1) why only MTX?
2) is it possible to fill the ATX mounts?

MY understanding (very limited) is that the mounts connect the engine/transmission to the subframe of the car, right? so therefore filling it with a hard substance (the polyurethane) cause the stiffness that cause the NVH but at the same time prevent or dramatically reduces the wheelhop associated with the engine itself moving?
I hope I'm getting all this correct.

Anywayz, it could be all wasted in my opinion anyway cause I have and CD4e...but that leads me back to the original questions..help me out please. Its not that I plan on racing my slushbox..lol, its just I figure since I'm changing mounts soon I might as well see if they can be filled.

~darp~



--------------------
Originally posted by PÕWDÉ®CØÃTMÀN:
I can do anything if i can find that powder .




Post Extras: Print Post Remind Me! Notify Moderator
Pole120
Hard-core CEG'er

Reged: 03/16/04
Posts: 4141
Loc: New Berlin, WI
Re: P.R.T. Poly Roll Resistors new
#1128940 (Re: darpinian) 12/19/05 02:11 PM

Originally posted by darpinian:
I have a couple of questions..

1) why only MTX?




I can do the front for either transmition as they're the same. I only have a jig to do a solid poly rear for the MTX, the ATX mount is a bit different, however i could fill it like i do the fronts.


Originally posted by darpinian:
2) is it possible to fill the ATX mounts?




See above.

Originally posted by darpinian:
MY understanding (very limited) is that the mounts connect the engine/transmission to the subframe of the car, right? so therefore filling it with a hard substance (the polyurethane) cause the stiffness that cause the NVH but at the same time prevent or dramatically reduces the wheelhop associated with the engine itself moving?


~darp~






Correct.

--------------------
99 SE V6\5spd - 156 HP\157 TQ 15.166-90.84
Totaled 02/12/06

99 SVT # 1571 - 175 HP\153 TQ 14.999-91.88
Born 3/24/99 Reborn 3/18/06
Pietenpol Racing Technologies project vehicle

90 Festiva L 5spd, Blue(not for long), 103k

Post Extras: Print Post Remind Me! Notify Moderator
Pole120
Hard-core CEG'er

Reged: 03/16/04
Posts: 4141
Loc: New Berlin, WI
Re: P.R.T. Poly Roll Resistors new
#1129038 (Re: Pole120) 12/19/05 04:10 PM

3 REARS

3 FRONTS



--------------------
99 SE V6\5spd - 156 HP\157 TQ 15.166-90.84
Totaled 02/12/06

99 SVT # 1571 - 175 HP\153 TQ 14.999-91.88
Born 3/24/99 Reborn 3/18/06
Pietenpol Racing Technologies project vehicle

90 Festiva L 5spd, Blue(not for long), 103k

Post Extras: Print Post Remind Me! Notify Moderator
darpinian
CEG'er

Reged: 10/09/03
Posts: 301
Loc: San Antonio Tx
Re: P.R.T. Poly Roll Resistors new
#1131069 (Re: Pole120) 12/21/05 09:02 PM

ok so the next question is..since you can do it for the ATX, Will you? and will the price be the same?

BTW I was talking to a few mechanics who I think are trying to screw me outta money. They're telling me they have to remove the exhaust manifolds and stuff to get to the rear mount and its gonna take 2-3 hours minimum. I looked on this site and it pretty much says theres 4 screws.. to remove and then brace the engine and put the new mount in. Is that all? Oh and is there like a break in period for the mounts?

~darp~


--------------------
Originally posted by PÕWDÉ®CØÃTMÀN:
I can do anything if i can find that powder .




Post Extras: Print Post Remind Me! Notify Moderator
Pole120
Hard-core CEG'er

Reged: 03/16/04
Posts: 4141
Loc: New Berlin, WI
Re: P.R.T. Poly Roll Resistors new
#1131089 (Re: darpinian) 12/21/05 09:17 PM

I have a very milited knowledge bas reguarding the rar ATX mount, the "4-bolts and it's out" method applies to the MTX mount, not necesarily the ATX. The price would be the same and i'ld need your rear mount to fill as i will never have a core. No break in period.

--------------------
99 SE V6\5spd - 156 HP\157 TQ 15.166-90.84
Totaled 02/12/06

99 SVT # 1571 - 175 HP\153 TQ 14.999-91.88
Born 3/24/99 Reborn 3/18/06
Pietenpol Racing Technologies project vehicle

90 Festiva L 5spd, Blue(not for long), 103k

Post Extras: Print Post Remind Me! Notify Moderator
Pole120
Hard-core CEG'er

Reged: 03/16/04
Posts: 4141
Loc: New Berlin, WI
Re: P.R.T. Poly Roll Resistors new
#1134155 (Re: Pole120) 12/28/05 05:51 PM

Note: I'll be off the boards for a week or two, if you need to contact me please do so via e-mail at pole120@hotmail.com and i'll try to get back to you if\when i can.

--------------------
99 SE V6\5spd - 156 HP\157 TQ 15.166-90.84
Totaled 02/12/06

99 SVT # 1571 - 175 HP\153 TQ 14.999-91.88
Born 3/24/99 Reborn 3/18/06
Pietenpol Racing Technologies project vehicle

90 Festiva L 5spd, Blue(not for long), 103k

Post Extras: Print Post Remind Me! Notify Moderator
Pole120
Hard-core CEG'er

Reged: 03/16/04
Posts: 4141
Loc: New Berlin, WI
Re: P.R.T. Poly Roll Resistors new
#1140071 (Re: Pole120) 01/06/06 02:00 PM

Bump. There has been an amendment to the first page of the thread with some new information.

2 REARS

2 FRONTS

ready to ship

--------------------
99 SE V6\5spd - 156 HP\157 TQ 15.166-90.84
Totaled 02/12/06

99 SVT # 1571 - 175 HP\153 TQ 14.999-91.88
Born 3/24/99 Reborn 3/18/06
Pietenpol Racing Technologies project vehicle

90 Festiva L 5spd, Blue(not for long), 103k

Post Extras: Print Post Remind Me! Notify Moderator
striker2
Veteran CEG'er

Reged: 03/15/04
Posts: 536
Loc: Glendale Heights, Il (for now)
Re: P.R.T. Poly Roll Resistors new
#1140110 (Re: Pole120) 01/06/06 03:09 PM

josh dont forget about amending the post to exlude pre-98 unless they send you theirs first. you know how many problems we had with mine.

oops should have read the first page first.

--------------------
97 contour gl mtx
front & rear upper strut tower braces
19mm bat sway bar
Koni struts w/GC knockoffs


Edited by striker2 (01/06/06 03:12 PM)

Post Extras: Print Post Remind Me! Notify Moderator
Pole120
Hard-core CEG'er

Reged: 03/16/04
Posts: 4141
Loc: New Berlin, WI
Re: P.R.T. Poly Roll Resistors new
#1147301 (Re: Pole120) 01/16/06 02:04 PM

Bump

2 REARS

2 FRONTS

ready to ship

--------------------
99 SE V6\5spd - 156 HP\157 TQ 15.166-90.84
Totaled 02/12/06

99 SVT # 1571 - 175 HP\153 TQ 14.999-91.88
Born 3/24/99 Reborn 3/18/06
Pietenpol Racing Technologies project vehicle

90 Festiva L 5spd, Blue(not for long), 103k

Post Extras: Print Post Remind Me! Notify Moderator
Pages: 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 | 17 | 18 | (show all)


Extra information
0 registered and 39 anonymous users are browsing this forum.

Moderator:  1314 

Print Thread

Permissions
You cannot start new topics
You cannot reply to topics
HTML is disabled
UBBCode is enabled

Thread views: 24364

Jump to

Contact Us Contour.org

*
UBB.threads™ 6.2.3

Generated in 0.018 seconds in which 0.011 seconds were spent on a total of 14 queries. Zlib compression enabled.

Copyright 1999-2005 Lance Kinley

CEG and contour.org are not affiliated with nor endorsed by Ford Motor Company