Swazo
(Hard-core CEG'er)
04/02/05 06:31 PM
Extrude Hone GB- Directly through EH

For those who've been waiting for an Extrude Hone GB for the UIM's, here you go. I got this email from Rick @ EH in reguards to the rumor about a set price of $285 for CEGers.

"Daymon, Hello the cost of $285.00 is for a group buy of 6 0r more
intakes. I have seen tuck tape on the intakes to protect them.
Thanks,

Rick Miller
Automotive Project Manager
Extrude Hone"

I know I'm not the only one who needs to get this done. Once we have enough, I'll get supply payment info that's directly through EH.

1. Swazo
2.
3.
4.
5.
6.
...


PÕWDÉ®CØÃTMÀŃ
(Hard-core CEG\'er)
04/02/05 08:06 PM
Re: Extrude Hone GB- Directly through EH

I have a friend who would do this , Is 285.00 the final price with return shipping ...Whats the HP gain if any ?

Pudmunkie
(Hard-core CEG\'er)
04/02/05 10:32 PM
Re: Extrude Hone GB- Directly through EH

So this is the uber extrude hone and can be done again to SVT UIMs correct


Russell-3L
(Hard-core CEG'er)
04/02/05 10:51 PM
Re: Extrude Hone GB- Directly through EH

i think i should let my 3L breathe a little better, count me in!

1. Swazo
2. Russell-3L
3.
4.
5.
6.


PÕWDÉ®CØÃTMÀŃ
(Hard-core CEG\'er)
04/02/05 11:20 PM
Re: Extrude Hone GB- Directly through EH

I have a friend who would do this for sure , but i read in another GB about the same product and they said there was no HP gains at all . . ?

Swazo
(Hard-core CEG'er)
04/04/05 01:50 AM
Re: Extrude Hone GB- Directly through EH

If there was no gain to this, then I wouldn't be spending $285 for it. Gains will depend on your mods. For example, a turbo 3L w/ PnP'd heads will get more gains than a basicly stock SVT from this mod.

Originally posted by Dan Nixon:
Awhile back I got some approx CFU rates from Extrude Hone..
stock = 155 CFU
single= 170 CFU
double= 180 CFU
triple= 188-190 CFU

We also know the SVT heads were flowed at 210-215 CFU (stock is about 195)..and t.body is reportedly over 300 CFU. So the point is that even on a 2.5L the UIM may be flow limiting factor along with LIM butterflies..




Swazo
(Hard-core CEG'er)
04/04/05 01:52 AM
Re: Extrude Hone GB- Directly through EH

Originally posted by Pudmunkie:
So this is the uber extrude hone and can be done again to SVT UIMs correct





Correct, max extrude honing for $285. I don't think return shipping is included..... I will double check or if anyone knows please pipe in.


NVSVT
(CEG\'er)
04/04/05 02:22 AM
Extrude Hone GB- Directly through EH

For $285 Extrude Hone will port-match your upper intake manifold to your lower intake manifold and hone the manifold another time with a "more agressive" putty. When completed your upper intake manifold will flow approximately 190 CFM. Shipping is not included in the $285 price.

beyondloadedSE
(Hard-core CEG'er)
04/04/05 06:51 PM
Re: Extrude Hone GB- Directly through EH

Whats the turn around time?

Will extrude hone effect my manifold if its powdercoated?


morbid
(Veteran CEG\'er)
04/04/05 11:31 PM
Re: Extrude Hone GB- Directly through EH

don't think that would matter as the SVT UIM's are all powdercoated. If you're really concerned about your finish (as I should have been), you might want to get that clear protective tape to put on the powercoated parts. I was in the last GB and my UIM had wear marks, though not that bad. Most likely was from shipping... from the UIM rubbing on their packing foam.

Swazo
(Hard-core CEG'er)
04/05/05 09:58 PM
Re: Extrude Hone GB- Directly through EH

My UIM is polished and hasn't been clear coated yet, so I HAVE to be careful with it. I was thinking about wrapping the runners/top with masking tape and cardboard. Rick pointed out that some just add duct tape on top and that has been fine.

Swazo
(Hard-core CEG'er)
04/11/05 09:57 PM
Re: Extrude Hone GB- Directly through EH

ttt


1. Swazo
2. Russell-3L
3.
4.
5.
6.


I'm calling Rick today to make sure what the turn around time is, I need to get mine back ASAP when this happens.


Outlaw4Shrt
(Newbie)
04/14/05 01:00 AM
Re: Extrude Hone GB- Directly through EH

I'll take one for my 3L as well. I just e-mail rick miller from the extrudehone.com website and then I saw this. Count me in for one. Thanks.

Adrian


Swazo
(Hard-core CEG'er)
04/27/05 08:52 PM
Re: Extrude Hone GB- Directly through EH



1. Swazo
2. Russell-3L
3. Outlaw4shrt
4.
5.
6.


I thought I'd posted this info but, turn around time for this is 2-3 weeks



Contact Us Contour.org

*
UBB.threads™ 6.2.3

Generated in 0.083 seconds in which 0.081 seconds were spent on a total of 4 queries. Zlib compression enabled.

Copyright 1999-2005 Lance Kinley

CEG and contour.org are not affiliated with nor endorsed by Ford Motor Company