TRicker
(CEG\'er)
07/10/06 01:50 AM
warmonger............FORMER owner of a csvt????

maybe i was just born yesterday, but what were you thinking warmonger? i feel betrayed!

why would you sell the CSVT!!!!


CSVT1214
(Hard-core CEG\'er)
07/10/06 01:51 AM
Re: warmonger............FORMER owner of a csvt????

PM's are cool.

Ray
(Addicted CEG\'er)
07/10/06 01:52 AM
Re: warmonger............FORMER owner of a csvt???

He sold it because he chose to...

because he had built an incredible machine..
and because he was at a point in his life that he knew he had bigger and better plans!































That, and because I wanted to buy it!



TRicker
(CEG\'er)
07/10/06 01:54 AM
Re: warmonger............FORMER owner of a csvt???

cool. anybody know what his bigger and better plans are???

oh and yeah i dont PM him because he doesnt check them much anymore it seems and this is easier, talking to you folks

oh and ray, i am supposed to ask how much its going to cost for a schematic of your turbo mani setup off that car!!!!


Ray
(Addicted CEG\'er)
07/10/06 01:59 AM
Re: warmonger............FORMER owner of a csvt???

Originally posted by TRicker:
cool. anybody know what his bigger and better plans are???



When it comes to Tom, you can NEVER TELL!!!! He'll surprise anyone, I am sure, when he gets in to a project!



beyondloadedSE
(Hard-core CEG'er)
07/10/06 02:07 AM
Re: warmonger............FORMER owner of a csvt???

Ray, when did you get new dyno numbers? Are they official?

svt4stv
(Addicted CEG\'er)
07/10/06 02:18 AM
Re: warmonger............FORMER owner of a csvt???

Originally posted by SVT4STD:
PM's are cool.




meh, over-rated


i am personally a big fan of the "shout out!" HOLLAAA!


Ray
(Addicted CEG\'er)
07/10/06 02:39 AM
Re: warmonger............FORMER owner of a csvt???

That's a gray area. I had a minor problem on the car, and once out of the shop I dyno'd to make sure it was where I was when I put it IN the shop. I went ahead and popped off a 14psi run to see where I stood.

Since that run, I have been talking with Tom about trying to get the car's tune shifted a bit, as I am now running rich, (faulty MAF replaced, threw off the tables, slightly)

I don't have a scan of the dyno sheet to post, but could always get one. I can't, however, swear that it would pull that again (right now) with it running rich. I think after I get it dialed in a little tighter, I will dyno again, and see what I can top, then.

So, the numbers were "officially" done, but aren't officially posted, as I don't have the scan of the sheet available.


morbid
(Veteran CEG\'er)
07/10/06 05:18 AM
Re: warmonger............FORMER owner of a csvt???

Originally posted by TRicker:
cool. anybody know what his bigger and better plans are???

oh and yeah i dont PM him because he doesnt check them much anymore it seems and this is easier, talking to you folks

oh and ray, i am supposed to ask how much its going to cost for a schematic of your turbo mani setup off that car!!!!




Dood... with warmonger being the great guy he is, he has many pictures and details freely available on his site.


RTStabler51
(Hard-core CEG'er)
07/10/06 02:00 PM
Re: warmonger............FORMER owner of a csvt???

if those numbers in your sig are it, than thats badass for stock internaled, homebuilt turbo car

TRicker
(CEG\'er)
07/11/06 12:35 AM
Re: warmonger............FORMER owner of a csvt???

Dood... with warmonger being the great guy he is, he has many pictures and details freely available on his site.






yep he has pics up. i asked him about it and he said that he didnt have any specs for the manifold he built, and that i should ask ray because he's a good guy and might help me out, when he needs to pull it off at least



Contact Us Contour.org

*
UBB.threads™ 6.2.3

Generated in 0.02 seconds in which 0.018 seconds were spent on a total of 4 queries. Zlib compression enabled.

Copyright 1999-2005 Lance Kinley

CEG and contour.org are not affiliated with nor endorsed by Ford Motor Company