PDA

View Full Version : Kaboom

Redlineracer12
07-01-2007, 05:01 PM
Here are some pics that Tyler requested.

on the side of an entrance ramp getting on 494.

http://www.uwrf.edu/~w3013194/Engine%20002.jpg
http://www.uwrf.edu/~W3013194/EnginePieces.JPG

More pictures to come this week when I finish pulling the heads. (Engine is already out)
Redlineracer12
07-02-2007, 12:38 AM
After slaving over the engine stand all evening I pulled all my timing components and got the cylinder heads off. It's pretty brutal. Turns out I had two bad pistons and my dad and I's theory is that the wrist pin failed causing that piston to lock up and those rods are pretty tough so something had to give.

http://www.uwrf.edu/~W3013194/Engine001.jpg

http://www.uwrf.edu/~W3013194/Engine006.jpg

http://www.uwrf.edu/~W3013194/Engine008.jpg

http://www.uwrf.edu/~W3013194/Engine009.jpg

http://www.uwrf.edu/~W3013194/Engine010.jpg

http://www.uwrf.edu/~W3013194/Engine011.jpg

http://www.uwrf.edu/~W3013194/Engine012.jpg

http://www.uwrf.edu/~W3013194/Engine013.jpg

Photography by Sandy
elraido
07-02-2007, 10:10 AM
engine looks fine to me. :)
Redlineracer12
07-02-2007, 10:14 AM
engine looks fine to me. :)

LOL just need one of them rebuild kit do-hickeys...
elraido
07-02-2007, 11:43 AM
little bit of superglue, ducttape, and jb weld and you are fine.
striker2
07-02-2007, 11:47 AM
Looks about like what happened to my friend Toms GP GTP engine. he lives up there in Inver Grove. Blue 98 GTP with a full race block, rebuilt the trans about 3 times. happen to know him?
KyleQ
07-02-2007, 12:33 PM
Ikes - stop littering with your rotating internals!
Redlineracer12
07-02-2007, 12:46 PM
Looks about like what happened to my friend Toms GP GTP engine. he lives up there in Inver Grove. Blue 98 GTP with a full race block, rebuilt the trans about 3 times. happen to know him?

Yes I know Tom, he has the daytona pace car edition. He only lives about 3 houses away from me :laugh:


JB weld ftw!
striker2
07-02-2007, 02:21 PM
he was my roommate in chicago at UTI.
Redlineracer12
07-02-2007, 02:25 PM
Nice I know a few people that have gone there. I've rode in his car before, it didn't seem too fast at the time :shrug:
striker2
07-02-2007, 04:02 PM
yeah the ol automatic makes it feel really slow. to bad GM never cme out with a manual version, they would have kicked ass.
Redlineracer12
07-02-2007, 04:04 PM
yeah the ol automatic makes it feel really slow. to bad GM never cme out with a manual version, they would have kicked ass.

Yeah and I've never seen much for those autos holding up much more than a stock GTP much less a built one. I do remember seeing one at the track with an intercooler that put down like low 12s in the 1/4 so he must've figured something out ;)
XKontour98
07-03-2007, 05:57 PM
Damn Tony what are you doing to your car! Learn to drive! ;)
Redlineracer12
07-03-2007, 06:31 PM
Damn Tony what are you doing to your car! Learn to drive! ;)

Driving is not the problem... just has too much dang powa! :laugh:

Actually I think that motor was junk from day one. I'm not buying a used block again.

Don't worry already got new better plans in the works :)
TRicker
07-04-2007, 03:51 PM
thanks for the pics, good luck with the "new" plan, i hope that works well! <wink wink> im sure IT WILL or the warranty will cover it haha. call me when you get it in, i'll pick up the hoist and get a ride!
Redlineracer12
07-05-2007, 05:04 PM
thanks for the pics, good luck with the "new" plan, i hope that works well! <wink wink> im sure IT WILL or the warranty will cover it haha. call me when you get it in, i'll pick up the hoist and get a ride!

Lol I will but I have no idea when I'm going to be done... I am done with the hoist now though (at least til I get everything else ready to go) so if you need it back you can get it anytime. I'm working on finding someone to get a complete valve job done.